DS90UB926Q-Q1 Datasheet, PDF (6/57 Pages) Texas Instruments – 5- to 85-MHz 24-Bit Color FPD-Link III Deserializer With Bidirectional Control Channel

DS90UB926Q-Q1
SNLS422B – JULY 2012 – REVISED JANUARY 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
See ^{(1) (2) (3) (4)}.
MIN
MAX
UNIT
Supply Voltage – V_DD33
Supply Voltage – V_DDIO
LVCMOS I/O Voltage
−0.3
4.0
V
−0.3
4.0
V
−0.3
(V_DDIO +
0.3)
V
Deserializer Input Voltage
−0.3
2.75
V
Junction Temperature
150
°C
Storage temperature, T_stg
Maximum Power Dissipation
Capacity at 25°C
R_θJA
R_θJC
−65
150
°C
31
°C/W
2.4
°C/W
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) The maximum limit (V_DDIO +0.3V) does not apply to the PDB pin during the transition to the power down state (PDB transitioning from
HIGH to LOW).
(4) For soldering specifications: see product folder at www.ti.com and SNOA549.
6.2 ESD Ratings
V_(ESD)
Electrostatic
discharge
Human-body model (HBM), per AEC Q100-002⁽¹⁾
Charged-device model (CDM), per AEC Q100-011
Machine model
(IEC, powered-up only)
R_D = 330 Ω, C_S = 150 pF
Air Discharge (Pin 49 and 50)
Contact Discharge (Pin 49 and 50)
(ISO1060SN5), R_D = 330 Ω
C_S = 150 pF
Air Discharge (Pin 49 and 50)
Contact Discharge (Pin 49 and 50)
(ISO10605), R_D = 2 kΩ
C_S = 150 and 330 pF
Air Discharge (Pin 49 and 50)
Contact Discharge (Pin 49 and 50)
VALUE
±8000
±1250
±250
±15000
±8000
±15000
±8000
±15000
±8000
(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
UNIT
V
6.3 Recommended Operating Conditions
MIN NOM MAX UNIT
Supply Voltage (V_DD33)
LVCMOS Supply Voltage (V_DDIO)
Operating Free Air
PCLK Frequency
Supply Noise⁽¹⁾
Temperature (T_A)
Connect V_DDIO to 3.3 V and use 3.3-V IOs
Connect V_DDIO to 1.8 V and use 1.8-V IOs
3
3
1.71
−40
5
3.3 3.6 V
3.3 3.6 V
1.8 1.89 V
+25 +105 °C
85 MHz
100 mV_P-P
(1) Supply noise testing was done with minimum capacitors on the PCB. A sinusoidal signal is AC coupled to the V_DD33 and V_DDIOsupplies
with amplitude = 100 mVp-p measured at the device V_DD33 and V_DDIO pins. Bit error rate testing of input to the Ser and output of the
Des with 10 meter cable shows no error when the noise frequency on the Ser is less than 50MHz. The Des on the other hand shows no
error when the noise frequency is less than 50 MHz.
6
Submit Documentation Feedback
Copyright © 2012–2015, Texas Instruments Incorporated
Product Folder Links: DS90UB926Q-Q1