NS32FV100 Datasheet, PDF (19/96 Pages) Texas Instruments – NS32FX100 NS32FV100 NS32FX200 System Controller

2 0 Architecture (Continued)
SDTGC Transmit Gain Control register Used to attenuate
the transmit IIR input samples The value to be
written in SDTGC register is 16384 c 10^{(Gain 20)}
rounded to the nearest integer number
Some examples are given in the following table
RIRQ
TIRQ
Mask Receive Interrupt Request
0 SDSTAT RIRQ will not cause an interrupt
1 SDSTAT RIRQ will cause an interrupt
Mask Transmit Interrupt Request
0 SDSTAT TIRQ will not cause an interrupt
Gain (dB)
b42
b41 9
SDTGC
0x0082
0x0084
1 SDSTAT TIRQ will cause an interrupt
RERR Mask Receive Error
0 SDSTAT RER will not cause an interrupt
1 SDSTAT RER will cause an interrupt
TERR Mask Transmit Error
0
0x4000
0 SDSTAT TER will not cause an interrupt
SDSTAT Status Register Provides information about the
1 SDSTAT TER will cause an interrupt
status of the Sigma-Delta operation
7
6
5
4
3
2
1
0
TSAT RSAT TFNE RFNE TERR RERR TIRQ RIRQ
te ^RIRQ
When ‘‘1’’ during receive enable (SDCNTL REe1)
it indicates that N or more samples are ready in the
receive FIFO This bit will remain high as long as the
number of samples is greater than or equal to N If
this bit is not masked by SDMASK RIRQ it will cause
an interrupt
TIRQ
When ‘‘1’’ during transmit enable (SDCNTL TEe1)
it indicates that less than N samples are ready in the
transmit FIFO This bit will remain high as long as
the number of samples is less than N If this bit is not
masked by SDMASK TIRQ it will cause an interrupt
RERR When ‘‘1’’ during receive enable (SDCNTL REe1) it
le ^{indicates an attempt to read an empty receive FIFO}
or incoming sample when the receive FIFO is full If
this bit is not masked by SDMASK RERR it will
cause an interrupt
TERR When ‘‘1’’ during transmit enable (SDCNTL TEe1)
it indicates an attempt to read from an empty trans-
mit FIFO or writing to a full transmit FIFO If this bit
o ^{is not masked by SDMASK TERR it will cause an}
interrupt
TFNE Transmit FIFO Not Empty when ‘‘0’’ indicates that
the transmit FIFO is empty
s RFNE Receive FIFO Not Empty when ‘‘0’’ indicates that
the receive FIFO empty
RSAT Reception Saturation This bit is set to ‘‘1’’ whenev-
er a saturation value is created in the receive IIR
(including the echo-canceling filter when enabled)
b ^{or in the receive gain control logic}
TSAT Transmit Saturation This bit is set to ‘‘1’’ whenever
a saturation value is created in the transmission IIR
or in DSDM
Upon reset all implemented bits in the SDSTAT reg-
ister are cleared to ‘‘0’’
O ^{SDMASK Mask Register Enables masking of SDC inter-}
2 3 6 Usage Recommendations
The SDC should be enabled (by setting the SDC bit in the
MCFG register to ‘‘1’’) before programming SDMASK and
SDCNTL
2 4 SCANNER CONTROLLER (SCANC)
2 4 1 Features
 Programmable generation of control signals which sup-
port a wide range of Charge Coupled Device (CCD) and
Contact Image Sensor (CIS) scanners
 Supports line scan times of 2 5 ms 5 ms 10 ms and
20 ms
 On-Chip shading-correction circuitry using reference line
values stored in the system RAM via DMA channel 0
 On-Chip dithering and Gamma correction circuit of 16
grey levels (64 grey levels in NS32FX200)
 Support for Automatic Background Control (ABC) and
edge enhancement with external circuitry
 On-Chip multiplying Digital-to-Analog Converter (DAC)
for compensation of scanner offset
 Automatic writing of scanned bitmap to memory via DMA
channel 2
 Optional bypass of on-chip video-data generation to sup-
port external image enhancement
2 4 2 Operation
The Scanner Controller Module (SCANC) consists of a
scanner signals generator block a video handling block
(shading compensation dithering and bitmap accumulation)
and a stepper motor control block The module includes
analog and digital circuits It uses two DMA channels one
for fetching a reference line and one for storing the digitized
video data The module is synchronized with the TCU mod-
ule The operation of SCANC and the allocation of DMA
channels 0 and 2 to the Scanner Controller or for external
usage are controlled by the Module Configuration Register
(MCFG) The module’s minimum operation frequency is
14 7456 MHz (i e it can not operate in Power Save mode)
Some of the Scanner signals can be assigned to an I O port
rupts
when the Scanner is not used (e g after reset)
7
4
3
2
1
0
res
TERR RERR TIRQ RIRQ
18