NS32FV100 Datasheet, PDF (18/96 Pages) Texas Instruments – NS32FX100 NS32FV100 NS32FX200 System Controller

2 0 Architecture (Continued)
2 3 4 1 Analog Transmitter
The input to the transmit analog circuit is the serial bit
stream at OSR which is generated by DSDM This serial bit
stream is fed to a 1-bit D A converter This D A converter is
implemented by an analog switch which selects either a5V
or b5V inputs These voltages are filtered by an RC low-
frequency Low Pass Filter (LPF) to filter supply noise and
to avoid crosstalk between the transmit and receive circuits
The D A output is filtered by a three pole LPF with unity
gain to attenuate the out-of-band quantization noise The
output of the LPF passes through a 600X resistor
PRES CTTL prescale The SDC over-sampling rate is gen-
erated by dividing the CTTL clock by a pre-scale di-
vider The PRES value is calculated as follows
PRES e (CTTL OSR) - 1
Some examples for sample rate 9 6 kHz and 8 kHz are giv-
en below
SDCNTL PRES
CTTL Frequency
(Sample Rate
9 6 kHz)
CTTL Frequency
(Sample Rate
8 0 kHz)
2 3 4 2 Analog Receiver
01011
14 7456 MHz
12 2880 MHz
The reception analog circuit obtains its analog input signal
from an isolation transformer The signal passes through a
01110
01111
18 4320 MHz
19 6608 MHz
15 3600 MHz
16 3840 MHz
buffer amplifier and then enters the Sigma Delta second
order loop The amplifier has two gain levels One gain level
provides a total gain of 0 dB and the second level provides
a total gain of 9 dB The two gain level are controlled by the
GAIN signal
The Sigma Delta second order loop contains two integrators
and a comparator to zero The comparator output is the
SDIN input to the on-chip Sigma Delta part SDIN is sam-
pled on-chip at OSR is passed to the digital filters and re-
te ^{turns as feedback (SDFDBK pin) to the analog part This}
feedback enters a 1-bit D A converter This D A converter
is implemented by an analog switch which selects either
a5V or b5V inputs These voltages are filtered by an RC
low frequency LPF to reduce supply noise and to avoid
crosstalk between the transmit and receive circuits The
feedback is an input to the first integrator unit
le ^{The receiver analog circuit can be calibrated by receiving a}
known reference voltage When the circuit is calibrated the
receiver input signal is a known reference voltage (V_REF)
otherwise the receiver input is the input signal from the iso-
lation transformer
2 3 5 Registers
The following is a partial list of registers For a full list see
o _{the detailed SD documentation available to source-level}
customers
s ^SDTX
Sigma-Delta Transmit Data This register is the
transmit FIFO port Any attempt to read from this
register will cause an unpredictable result
SDRX
Sigma-Delta Transmit Data This register is the re-
ceive FIFO port Any attempt to write to this regis-
ter will cause an unpredictable result
SDCNTL Control register
b _{15 13 12 11}
7 6 54
321
0
N A N A PRES N A TE N A RE N A
Upon reset SDCNTL PRES is loaded at the minimum pre-
scale value in Full-duplex mode ‘‘01001’’ All other imple-
O ^{mented bits of SDCNTL are cleared to ‘‘0’’}
10000
10001
10010
10011
20 8896 MHz
22 1184 MHz
23 3472 MHz
24 5760 MHz
17 4080 MHz
18 4320 MHz
19 4560 MHz
20 4800 MHz
SDFTM Fine Timing register
7
4
3
res
ADV
2
0
STEP
STEP
ADV
SDRGC
Advance or delay steps amount (0–7)
Advance direction
0 Delay mode is enabled
1 Advance mode is enabled
Writing to this register while SDCNTL RE is ac-
tive is allowed only if SDFTM STEP is equal to a
‘‘0’’
Writing to this register while both SDCNTL RE is
active and SDFTM STEP is not ‘‘0’’ will cause an
unpredictable result
While SDCNTL RE is active this register holds
the number of advance or delay steps yet to be
executed
Receive Gain Control register Used to amplify or
attenuate the receive IIR output samples The
value to be written in SDRGC register is 128 c
10^{(Gain 20)} rounded to the nearest integer num-
ber
Some examples are given in the following table
Gain (dB)
b18
b17 5
SDRGC
0x0010
0x0011
0
0x0080
01
0x0081
NOTE Bits marked N A are available only for source-level customers For
other customers they must not be modified
RE Enables or disables receive mode
0 Receive mode is disabled
48 0
0x7D98
1 Receive mode is enabled
TE Enables or disables transmit mode
0 Transmit mode is disabled
1 Transmit mode is enabled
17