4507_M Datasheet, PDF (172/216 Pages) Renesas Technology Corp – 4-BIT CISC SINGLE-CHIP MICROCOMPUTER 4500 SERIES

4507 Group
APPENDIX
3.1 Electrical characteristics
3.1.3 Electrical characteristics
Table 3.1.4 Electrical characteristics (Ta = –20 °C to 85 °C, VDD = 2.0 to 5.5 V, unless otherwise noted)
Symbol
Parameter
Test conditions
VOL
“L” level output voltage
VDD = 5.0 V
IOL = 12 mA
P0, P1
IOL = 4.0 mA
VDD = 3.0 V
IOL = 6.0 mA
IOL = 2.0 mA
VOL
“L” level output voltage
VDD = 5.0 V
IOL = 5.0 mA
P2, P3, RESET
IOL = 1.0 mA
VDD = 3.0 V
IOL = 2.0 mA
VOL
“L” level output voltage
VDD = 5.0 V
IOL = 30 mA
D0, D1
IOL = 10 mA
VDD = 3.0 V
IOL = 15 mA
IOL = 5.0 mA
VOL
“L” level output voltage
VDD = 5.0 V
IOL = 15 mA
D2/C, D3/K
IOL = 5.0 mA
VDD = 3.0 V
IOL = 9.0 mA
IOL = 3.0 mA
VOL
“L” level output voltage
VDD = 5.0 V
IOL = 15 mA
D4, D5
IOL = 5.0 mA
VDD = 3.0 V
IOL = 9.0 mA
IOL = 3.0 mA
IIH
“H” level input current
VI = VDD
P0, P1, P2, P3, RESET
IIH
“H” level input current
VI = VDD
D0, D1, D2/C, D3/K, D4, D5
IIL
“L” level input current
VI = 0 V P0, P1, P2 No pull-up
P0, P1, P2, P3
IIL
“L” level input current
VI = 0 V, D2/C, D3/K, No pull-up
D0, D1, D2/C, D3/K, D4, D5
IDD
Supply current at active mode
VDD = 5.0 V
High-speed mode
(Note 1)
f(XIN) = 4.0 MHz
Middle-speed mode
Low-speed mode
Default mode
VDD = 3.0 V
High-speed mode
f(XIN) = 2.0 MHz
Middle-speed mode
Low-speed mode
Default mode
at RAM back-up mode Ta = 25 °C
(POF2 instruction execution) VDD = 5.0 V
VDD = 3.0 V
RPU
Pull-up resistor value
VI = 0 V
VDD = 5.0 V
P0, P1, P2, D2/C, D3/K, RESET
VDD = 3.0 V
VT+ – VT– Hysteresis INT, CNTR
VDD = 5.0 V
VDD = 3.0 V
VT+ – VT– Hysteresis RESET
VDD = 5.0 V
VDD = 3.0 V
f(RING) On-chip oscillator clock frequency
(Note 2)
VDD = 5.0 V
VDD = 3.0 V
Limits
Unit
Min. Typ. Max.
2.0 V
0.9
0.9
0.6
2.0 V
0.6
0.9
2.0 V
0.9
2.0
0.9
2.0 V
0.9
2.0
0.9
2.0 V
0.9
2.0
0.9
1.0 µA
1.0 µA
–1.0
µA
–1.0
µA
1.7 5.0 mA
1.3 3.9
1.1 3.3
1.0 3.0
0.5 1.5
0.4 1.2
0.35 1.1
0.3 0.9
0.1 1.0 µA
10
6.0
30 60 150 kΩ
50 120 300
0.25
V
0.25
1.2
V
0.5
1.0 2.0 3.0 MHz
0.5 1.0 1.8
Notes 1: When the A/D converter is used, the A/D operation current (IADD) is included.
2: When system operates by the on-chip oscillator, the system clock frequency is the on-chip oscillator clock divided by the dividing ratio selected with
register MR.
Rev.2.01 Feb 04, 2005
3-6
REJ09B0195-0201