306666-11 Datasheet, PDF (92/99 Pages) Numonyx B.V – Numonyx StrataFlash Embedded Memory

P30
Table 42: Protection Register Information
Offset⁽¹⁾
P = 10Ah
(P+E)h
(P+F)h
(P+10)h
(P+11)h
(P+12)h
Length
1
4
Description
(Optional flash features and commands)
Number of Protection register fields in JEDEC ID space.
“00h,” indicates that 256 protection fields are available
Protection Field 1: Protection Description
This field describes user-available One Time Programmable
(OTP) Protection register bytes. Some are pre-programmed
with device-unique serial numbers. Others are user
programmable. Bits 0–15 point to the Protection register Lock
byte, the section’s first byte. The following bytes are factory
pre-programmed and user-programmable.
Add.
118:
119:
11A:
11B:
11C:
Hex
Code
--02
--80
--00
--03
--03
Value
2
80h
00h
8 byte
8 byte
bits 0–7 = Lock/bytes Jedec-plane physical low address
bits 8–15 = Lock/bytes Jedec-plane physical high address
bits 16–23 = “n” such that 2ⁿ = factory pre-programmed bytes
bits 24–31 = “n” such that 2ⁿ = user programmable bytes
(P+13)h
(P+14)h
(P+15)h
(P+16)h
(P+17)h
(P+18)h
(P+19)h
(P+1A)h
(P+1B)h
(P+1C)h
10 Protection Field 2: Protection Description
11D: --89 89h
Bits 0–31 point to the Protection register physical Lock-word 11E: --00 00h
address in the Jedec-plane.
11F: --00 00h
Following bytes are factory or user-programmable.
bits 32–39 = “n” ∴ n = factory pgm'd groups (low byte)
bits 40–47 = “n” ∴ n = factory pgm'd groups (high byte)
120: --00 00h
121: --00 0
122: --00 0
bits 48–55 = “n” \ 2n = factory programmable bytes/group 123: --00 0
bits 56–63 = “n” ∴ n = user pgm'd groups (low byte)
124: --10 16
bits 64–71 = “n” ∴ n = user pgm'd groups (high byte)
125: --00 0
bits 72–79 = “n” ∴ 2ⁿ = user programmable bytes/group
126: _--04 16
Table 43: Burst Read Information
Offset⁽¹⁾
P = 10Ah
(P+1D)h
(P+1E)h
(P+1F)h
(P+20)h
(P+21)h
(P+22)h
Length
1
1
1
1
1
1
Description
(Optional flash features and commands)
Page Mode Read capability
bits 0–7 = “n” such that 2ⁿ HEX value represents the number of
read-page bytes. See offset 28h for device word width to
determine page-mode data output width. 00h indicates no
read page buffer.
Number of synchronous mode read configuration fields that
follow. 00h indicates no burst capability.
Synchronous mode read capability configuration 1
Bits 3–7 = Reserved
bits 0–2 “n” such that 2ⁿ⁺¹ HEX value represents the
maximum number of continuous synchronous reads when
the device is configured for its maximum word width. A value
of 07h indicates that the device is capable of continuous
linear bursts that will output data until the internal burst
counter reaches the end of the device’s burstable address
space. This field’s 3-bit value can be written directly to the
Read Configuration Register bits 0–2 if the device is
configured for its maximum word width. See offset 28h for
word width to determine the burst data output width.
Synchronous mode read capability configuration 2
Synchronous mode read capability configuration 3
Synchronous mode read capability configuration 4
Hex
Add. Code Value
127: --03 8 byte
128: --04 4
129: --01 4
12A: --02
12B: --03
12C: --07
8
16
Cont
Datasheet
92
November 2007
Order Number: 306666-11