CP3BT26 Datasheet, PDF (25/278 Pages) National Semiconductor (TI) – Reprogrammable Connectivity Processor with Bluetooth-R, USB, and CAN Interfaces

6.4 BIU CONTROL REGISTERS
Table 7 Operating Environment Selection
ENV[2:0] EMPTY
Operating Environment
111
No Internal ROM enabled (IRE) mode
011
No External ROM enabled (ERE) mode
The BIU has a set of control registers that determine how
many wait cycles and hold cycles are to be used for access-
ing memory. During initialization of the system, these regis-
ters should be programmed with appropriate values so that
the minimum allowable number of cycles is used. This num-
ber varies with the clock frequency.
000
N/A Development (DEV) mode
There are five BIU control registers, as listed in Table 8.
001
N/A
Development (DEVINT) mode with
internal memory
These registers control the bus cycle configuration used for
accessing the various on-chip memory types.
110
N/A In-System-Programming (ISP) mode
Table 8 Bus Control Registers
111
Yes In-System-Programming (ISP) mode
Name
Address
Description
011
Yes In-System-Programming (ISP) mode
6.2 BUS INTERFACE UNIT (BIU)
The BIU controls the interface between the CPU core bus
and those on-chip modules which are mapped into BIU
zones. These on-chip modules are the flash program mem-
ory and the I/O zone. The BIU controls the configured pa-
rameters for bus access (such as the number of wait states
for memory access) and issues the appropriate bus signals
for the requested access.
6.3 BUS CYCLES
There are four types of data transfer bus cycles:
„ Normal read
„ Fast read
„ Early write
„ Late write
The type of data cycle used in a particular transaction de-
pends on the type of CPU operation (a write or a read), the
type of memory or I/O being accessed, and the access type
programmed into the BIU control registers (early/late write
or normal/fast read).
BCFG
IOCFG
SZCFG0
SZCFG1
SZCFG2
FF F900h
FF F902h
FF F904h
FF F906h
FF F908h
BIU Configuration Register
I/O Zone Configuration
Register
Static Zone 0
Configuration Register
Static Zone 1
Configuration Register
Static Zone 2
Configuration Register
6.4.1 BIU Configuration Register (BCFG)
The BCFG register is a byte-wide, read/write register that
selects early-write or late-write bus cycles. At reset, the reg-
ister is initialized to 07h. The register format is shown below.
7
3
2
1
0
Reserved
1
1 EWR
For read operations, a basic normal read takes two clock cy-
cles, and a fast-read bus cycle takes one clock cycle. Nor-
mal read bus cycles are enabled by default after reset.
For write operations, a basic late-write bus cycle takes two
clock cycles, and a basic early-write bus cycle takes three
clock cycles. Early-write bus cycles are enabled by default
after reset. However, late-write bus cycles are needed for
ordinary write operations, so this configuration must be
changed by software (see Section 6.4.1).
In certain cases, one or more additional clock cycles are
added to a bus access cycle. There are two types of addi-
tional clock cycles for ordinary memory accesses, called in-
ternal wait cycles (TIW) and hold (Thold) cycles.
A wait cycle is inserted in a bus cycle just after the memory
address has been placed on the address bus. This gives the
accessed memory more time to respond to the transaction
request.
EWR
The Early Write bit controls write cycle timing.
0 – Late-write operation (2 clock cycles to
write).
1 – Early-write operation.
At reset, the BCFG register is initialized to 07h, which se-
lects early-write operation. However, late-write operation is
required for normal device operation, so software must
change the register value to 06h. Bits 1 and 2 of this register
must always be set when writing to this register.
A hold cycle is inserted at the end of a bus cycle. This holds
the data on the data bus for an extended number of clock cy-
cles.
25
www.national.com