PIC24HJ12GP201_11 Datasheet, PDF (200/262 Pages) Microchip Technology – High-Performance, 16-bit Microcontrollers 5-cycle latency

PIC24HJ12GP201/202
TABLE 22-17: PLL CLOCK TIMING SPECIFICATIONS (VDD = 3.0V TO 3.6V)
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
AC CHARACTERISTICS
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
Param
No.
Symbol
Characteristic
Min Typ⁽¹⁾ Max Units
Conditions
OS50 FPLLI
PLL Voltage Controlled
Oscillator (VCO) Input
Frequency Range
0.8
—
8
MHz ECPLL, HSPLL, XTPLL
modes
OS51 FSYS On-Chip VCO System Frequency 100
—
200 MHz
—
OS52 TLOCK PLL Start-up Time (Lock Time)
0.9
1.5
3.1 mS
—
OS53 DCLK
CLKO Stability (Jitter)⁽²⁾
-3
0.5
3
% Measured over 100 ms
period
Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only
and are not tested.
2: These parameters are characterized by similarity, but are not tested in manufacturing. This specification is
based on clock cycle by clock cycle measurements. To calculate the effective jitter for individual time bases
or communication clocks use this formula:
Peripheral Clock Jitter = ------------------------------^D----^C----^L---^K------------------------------
⎛
⎝
P^----e^---r^--i^--p^---h^---e^--r^---a^---lF^---B^-O---i^-St^--C--R^---a^---t^--e^----C^----l^--o^---c^--k^{- ⎠⎞}
For example: Fosc = 32 MHz, DCLK = 3%, SPI bit rate clock, (i.e., SCK) is 2 MHz.
SPI SCK Jitter = ---------^D----^C----^L---^K--------- = -3----%---- = ^3----%--- = 0.75%
⎛
⎝
3--2-2----_M--M_----H-H_---z--z_⎠⎞
16
4
TABLE 22-18: AC CHARACTERISTICS: INTERNAL RC ACCURACY
AC CHARACTERISTICS
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
Operating temperature
-40°C ≤TA ≤+85°C for industrial
-40°C ≤TA ≤+125°C for Extended
Param
No.
Characteristic
Min Typ Max Units
Conditions
Internal FRC Accuracy @ 7.3728 MHz⁽¹⁾
F20a FRC
-2
—
+2
%
-40°C ≤TA ≤+85°C
VDD = 3.0-3.6V
F20b FRC
-5
—
+5
%
-40°C ≤TA ≤+125°C
VDD = 3.0-3.6V
Note 1: Frequency calibrated at 25°C and 3.3V. TUN bits can be used to compensate for temperature drift.
TABLE 22-19: INTERNAL RC ACCURACY
AC CHARACTERISTICS
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
Param
No.
Characteristic
Min Typ Max Units
Conditions
LPRC @ 32.768 kHz^(1,2)
F21a LPRC
-20
±6
+20
%
-40°C ≤TA ≤+85°C
VDD = 3.0-3.6V
F21b LPRC
-70
—
+70
%
-40°C ≤TA ≤+125°C VDD = 3.0-3.6V
Note 1: Change of LPRC frequency as VDD changes.
2: LPRC accuracy impacts the Watchdog Timer Time-out Period (TWDT1). See Section 19.4 “Watchdog
Timer (WDT)” for more information.
DS70282E-page 200
© 2007-2011 Microchip Technology Inc.