UPSD3212A Datasheet, PDF (138/163 Pages) STMicroelectronics – Flash Programmable System Devices with 8032 MCU with USB and Programmable Logic

uPSD3212A, uPSD3212C, uPSD3212CV
Table 115. DC Characteristics (3V Devices)
Symbol
Parameter
Test Condition
(in addition to those
in Table
Min.
Typ. Max.
Unit
110., page 133)
Input High Voltage (Ports 1, 2,
V_IH
3, 4[Bits 7,6,5,4,3,1,0], A, B, C, 3.0V < VCC < 3.6V
0.7V_CC
D, XTAL1, RESET)
V_CC + 0.5
V
V_IH1
Input High Voltage (Port 4[Bit
2])
3.0V < V_CC < 3.6V
2.0
V_CC + 0.5
V
Input High Voltage (Ports 1, 2,
V_IL
3, 4[Bits 7,6,5,4,3,1,0], XTAL1, 3.0V < VCC < 3.6V VSS – 0.5
RESET)
0.3V_CC
V
Input Low Voltage
(Ports A, B, C, D)
V_IL1
Input Low Voltage
(Port 4[Bit 2])
3.0V < V_CC < 3.6V
3.0V < V_CC < 3.6V
–0.5
V_SS – 0.5
0.8
V
0.8
V
V_OL
Output Low Voltage
(Ports A,B,C,D)
I_OL = 20µA
V_CC = 3.0V
I_OL = 4mA
V_CC = 3.0V
0.01
0.1
V
0.15 0.45
V
V_OL1
Output Low Voltage
(Ports 1,2,3,4, WR, RD)
I_OL = 1.6mA
I_OL = 100µA
0.45
V
0.3
V
V_OL2
Output Low Voltage
(Port 0, ALE, PSEN)
I_OL = 3.2mA
I_OL = 200µA
0.45
V
0.3
V
V_OH
Output High Voltage
(Ports A,B,C,D)
I_OH = –20µA
V_CC = 3.0V
2.9
2.99
V
I_OH = –1mA
V_CC = 3.0V
2.4
2.6
V
V_OH1
Output High Voltage
(Ports 1,2,3,4, WR, RD)
I_OH = –20µA
2.0
I_OH = –10µA
2.7
V
V
V_OH2
Output High Voltage (Port 0 in
ext. Bus Mode, ALE, PSEN)
I_OH = –800µA
I_OH = –80µA
2.0
2.7
V
V
V_OH3
Output High Voltage V_STBYON
I_OH = –1µA
V_STBY – 0.8
V
V_LVR
Low Voltage Reset
0.1V hysteresis
2.3
2.5
2.7
V
V_OP
XTAL Open Bias Voltage
(XTAL1, XTAL2)
I_OL = 3.2mA
1.0
2.0
V
V_LKO
V_CC(min) for Flash Erase and
Program
1.5
2.2
V
V_STBY
SRAM (PSD) Standby Voltage
2.0
V_CC – 0.2
V
V_DF
SRAM (PSD) Data Retention
Voltage
Only on V_STBY
2
V
I_IL
Logic '0' Input Current
(Ports 1,2,3,4)
V_IN = 0.45V
(0V for Port 4[pin 2])
–1
–50
µA
138/163