DS923 Datasheet, PDF (2/56 Pages) Xilinx, Inc – DC and AC Switching Characteristics

Virtex UltraScale+ FPGA Data Sheet: DC and AC Switching Characteristics
Table 1: Absolute Maximum Ratings⁽¹⁾ (Cont’d)
Symbol
Description
Min
Max
Units
GTY Transceivers
V_MGTAVCC
Analog supply voltage for the GTY transmitter and receiver
circuits.
–0.500
1.000
V
V_MGTAVTT
Analog supply voltage for the GTY transmitter and receiver
termination circuits.
–0.500
1.300
V
V_MGTVCCAUX
Auxiliary analog Quad PLL (QPLL) voltage supply for the GTY
transceivers.
–0.500
1.900
V
V_MGTREFCLK
V_MGTAVTTRCAL
GTY transceiver reference clock absolute input voltage.
Analog supply voltage for the resistor calibration circuit of
the GTY transceiver column.
–0.500
–0.500
1.300
V
1.300
V
V_IN
Receiver (RXP/RXN) and transmitter (TXP/TXN) absolute
input voltage.
–0.500
1.200
V
I_DCIN-FLOAT
DC input current for receiver input pins DC coupled RX
termination = floating.
–
mA
I_DCIN-MGTAVTT
DC input current for receiver input pins DC coupled RX
termination = V_MGTAVTT.
–
I_DCIN-GND
DC input current for receiver input pins DC coupled RX
termination = GND.
–
0⁽⁷⁾
mA
0⁽⁷⁾
mA
I_DCIN-PROG
DC input current for receiver input pins DC coupled RX
termination = programmable.
–
0⁽⁷⁾
mA
I_DCOUT-FLOAT
DC output current for transmitter pins DC coupled RX
termination = floating.
–
mA
I_{DCOUT-MGTAVTT}
DC output current for transmitter pins DC coupled RX
termination = V_MGTAVTT.
–
mA
System Monitor
V_CCADC
System Monitor supply relative to GNDADC.
V_REFP
System Monitor reference input relative to GNDADC.
Temperature
0.500
0.500
2.000
V
2.000
V
T_STG
T_SOL
T_j
Storage temperature (ambient).
Maximum soldering temperature⁽⁸⁾.
Maximum junction temperature⁽⁸⁾.
–65
150
°C
–
260
°C
–
125
°C
Notes:
1. Stresses beyond those listed under Absolute Maximum Ratings might cause permanent damage to the device. These are
stress ratings only, and functional operation of the device at these or any other conditions beyond those listed under
Operating Conditions is not implied. Exposure to Absolute Maximum Ratings conditions for extended periods of time might
affect device reliability.
2. V_{CCINT_IO} must be connected to V_CCBRAM.
3. V_{CCAUX_IO} must be connected to V_CCAUX.
4. The lower absolute voltage specification always applies.
5. For I/O operation, see the UltraScale Architecture SelectIO Resources User Guide (UG571).
6. The maximum limit applied to DC signals. For maximum undershoot and overshoot AC specifications, see Table 4.
7. For more information on supported GTY transceiver terminations see the or UltraScale Architecture GTY Transceiver User
Guide (UG578)
8. For soldering guidelines and thermal considerations, see the UltraScale and UltraScale+ FPGA Packaging and Pinout
Specifications (UG575).
DS923 (v1.0) April 20, 2016
Advance Product Specification
www.xilinx.com
Send Feedback
2