LM3S5739 Datasheet, PDF (409/856 Pages) Texas Instruments – Stellaris® LM3S5739 Microcontroller

Stellaris® LM3S5739 Microcontroller
10.2
Signal Description
Table 10-2 on page 409 lists the external signals of the GP Timer module and describes the function
of each. The GP Timer signals are alternate functions for some GPIO signals and default to be
GPIO signals at reset. The column in the table below titled "Pin Assignment" lists the possible GPIO
pin placements for these GP Timer signals. The AFSEL bit in the GPIO Alternate Function Select
(GPIOAFSEL) register (page 378) should be set to choose the GP Timer function. For more information
on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 355.
Table 10-2. General-Purpose Timers Signals (100LQFP)
Pin Name
Pin Number Pin Type Buffer Type^a Description
CCP0
23
I/O
TTL
Capture/Compare/PWM 0.
CCP1
43
I/O
TTL
Capture/Compare/PWM 1.
CCP2
25
I/O
TTL
Capture/Compare/PWM 2.
CCP3
41
I/O
TTL
Capture/Compare/PWM 3.
CCP4
22
I/O
TTL
Capture/Compare/PWM 4.
CCP5
12
I/O
TTL
Capture/Compare/PWM 5.
CCP6
86
I/O
TTL
Capture/Compare/PWM 6.
CCP7
13
I/O
TTL
Capture/Compare/PWM 7.
a. The TTL designation indicates the pin has TTL-compatible voltage levels.
10.3
Functional Description
The main components of each GPTM block are two free-running 16-bit up/down counters (referred
to as TimerA and TimerB), two 16-bit match registers, and two 16-bit load/initialization registers and
their associated control functions. The exact functionality of each GPTM is controlled by software
and configured through the register interface.
Software configures the GPTM using the GPTM Configuration (GPTMCFG) register (see page 419),
the GPTM TimerA Mode (GPTMTAMR) register (see page 420), and the GPTM TimerB Mode
(GPTMTBMR) register (see page 422). When in one of the 32-bit modes, the timer can only act as
a 32-bit timer. However, when configured in 16-bit mode, the GPTM can have its two 16-bit timers
configured in any combination of the 16-bit modes.
10.3.1
GPTM Reset Conditions
After reset has been applied to the GPTM module, the module is in an inactive state, and all control
registers are cleared and in their default states. Counters TimerA and TimerB are initialized to
0xFFFF, along with their corresponding load registers: the GPTM TimerA Interval Load
(GPTMTAILR) register (see page 433) and the GPTM TimerB Interval Load (GPTMTBILR) register
(see page 434). The prescale counters are initialized to 0x00: the GPTM TimerA Prescale
(GPTMTAPR) register (see page 437) and the GPTM TimerB Prescale (GPTMTBPR) register (see
page 438).
10.3.2
32-Bit Timer Operating Modes
This section describes the three GPTM 32-bit timer modes (One-Shot, Periodic, and RTC) and their
configuration.
The GPTM is placed into 32-bit mode by writing a 0 (One-Shot/Periodic 32-bit timer mode) or a 1
(RTC mode) to the GPTM Configuration (GPTMCFG) register. In both configurations, certain GPTM
registers are concatenated to form pseudo 32-bit registers. These registers include:
November 17, 2011
409
Texas Instruments-Production Data