MSP430F6779A Datasheet, PDF (26/176 Pages) Texas Instruments – Polyphase Metering SoCs

MSP430F6779A, MSP430F6778A, MSP430F6777A, MSP430F6776A, MSP430F6775A
MSP430F6769A, MSP430F6768A, MSP430F6767A, MSP430F6766A, MSP430F6765A
MSP430F6749A, MSP430F6748A, MSP430F6747A, MSP430F6746A, MSP430F6745A
SLAS982 – MAY 2014
www.ti.com
5 Specifications
5.1 Absolute Maximum Ratings⁽¹⁾
over operating free-air temperature range (unless otherwise noted)
Voltage applied at DVCC to DVSS
Voltage applied to any pin (excluding VCORE)⁽²⁾
Diode current at any device pin
–0.3 V to 4.1 V
–0.3 V to V_CC + 0.3 V
±2 mA
Maximum junction temperature, T_J
95°C
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages referenced to V_SS. V_CORE is for internal device use only. No external DC loading or voltage should be applied.
5.2 Handling Ratings
MIN
MAX
UNIT
T_stg
Storage temperature range⁽¹⁾
-55
105
°C
(1) Higher temperature may be applied during board soldering according to the current JEDEC J-STD-020 specification with peak reflow
temperatures not higher than classified on the device label on the shipping boxes or reels.
5.3 Recommended Operating Conditions
Typical values are specified at V_CC = 3.3 V and T_A = 25°C (unless otherwise noted)
V_CC
V_SS
T_A
T_J
C_VCORE
C_DVCC/
C_VCORE
f_SYSTEM
I_LOAD,
DVCCD
I_LOAD,
AUX1D
I_LOAD,
AUX2D
I_LOAD,
AVCCA
Supply voltage during program execution and flash
programming. V_AVCC = V_DVCC = V_CC(1)(2)
Supply voltage V_AVSS = V_DVSS = V_SS
Operating free-air temperature
Operating junction temperature
Recommended capacitor at VCORE
PMMCOREVx = 0
PMMCOREVx = 0, 1
PMMCOREVx = 0, 1, 2
PMMCOREVx = 0, 1, 2, 3
I version
I version
Capacitor ratio of DVCC to VCORE
Processor frequency (maximum MCLK frequency)^{(3) (4)}
(see Figure 5-1)
Maximum load current that can be drawn from DVCC
for core and IO (I_LOAD = I_CORE + I_IO)
Maximum load current that can be drawn from
AUXVCC1 for core and IO (I_LOAD = I_CORE + I_IO)
Maximum load current that can be drawn from
AUXVCC2 for core and IO (I_LOAD = I_CORE + I_IO)
Maximum load current that can be drawn from AVCC
for analog modules (I_LOAD = I_Modules)
PMMCOREVx = 0,
1.8 V ≤ V_CC ≤ 3.6 V
(default condition)
PMMCOREVx = 1,
2 V ≤ V_CC ≤ 3.6 V
PMMCOREVx = 2,
2.2 V ≤ V_CC ≤ 3.6 V
PMMCOREVx = 3,
2.4 V ≤ V_CC ≤ 3.6 V
MIN NOM MAX UNIT
1.8
3.6 V
2.0
3.6 V
2.2
3.6 V
2.4
3.6 V
0
V
–40
85 °C
–40
85 °C
470
nF
10
0
8.0
0
12.0
MHz
0
20.0
0
25.0
20 mA
20 mA
20 mA
10 mA
(1) It is recommended to power AVCC and DVCC from the same source. A maximum difference of 0.3 V between V(AVCC) and V(DVCC)
can be tolerated during power up and operation.
(2) The minimum supply voltage is defined by the supervisor SVS levels when it is enabled. See the Table 5-14 threshold parameters for
the exact values and further details.
(3) The MSP430 CPU is clocked directly with MCLK. Both the high and low phase of MCLK must not exceed the pulse duration of the
specified maximum frequency.
(4) Modules may have a different maximum input clock specification. See the specification of the respective module in this data sheet.
26
Specifications
Copyright © 2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6779A MSP430F6778A MSP430F6777A MSP430F6776A MSP430F6775A
MSP430F6769A MSP430F6768A MSP430F6767A MSP430F6766A MSP430F6765A MSP430F6749A
MSP430F6748A MSP430F6747A MSP430F6746A MSP430F6745A