PIC18F86K22-I Datasheet, PDF (495/550 Pages) Microchip Technology – 64/80-Pin, High-Performance, 1-Mbit Enhanced Flash Microcontrollers

PIC18F87K22 FAMILY
31.2 DC Characteristics: Power-Down and Supply Current
PIC18F87K22 Family (Industrial/Extended) (Continued)
PIC18F87K22 Family
(Industrial/Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Device
Typ
Max Units
Conditions
Module Differential Currents (IWDT, IBOR, IHLVD, IOSCB, IAD)
D022
(IWDT)
D022
(IWDT)
Watchdog Timer
All devices 0.3
0.3
0.3
0.5
1
µA
1
µA
1
µA
2
µA
-40°C
+25°C
+85°C
+125ºC
VDD = 1.8V⁽⁴⁾
Regulator Disabled
All devices 0.6
2
µA
-40°C
0.6
2
µA
+25°C
VDD = 3.3V⁽⁴⁾
0.7
2
µA
+85°C
Regulator Disabled
1
3
µA
+125ºC
All Devices 0.6
2
µA
-40°C
0.6
2
µA
+25°C
VDD = 5V⁽⁵⁾
0.7
2
µA
+85°C
Regulator Enabled
1.5
4
µA
+125ºC
D022A
(IBOR)
(IBOR)
Brown-out Reset
All devices 4.6
4.5
4.7
19 µA
20 µA
20 µA
-40°C
+25°C
+85°C
VDD = 3.3V⁽⁴⁾
Regulator Disabled
High-Power BOR
18
40 µA
+125ºC
All devices 4.2
4.3
4.4
20 µA
20 µA
20 µA
-40°C
+25°C
+85°C
VDD = 5V⁽⁵⁾
Regulator Enabled
High-Power BOR
20
40 µA
+125ºC
D022B High/Low-Voltage Detect
(IHLVD)
All devices ^3.8
4.2
4.3
9
µA
9
µA
10 µA
-40°C
+25°C
+85°C
VDD = 1.8V⁽⁴⁾
Regulator Disabled
4.5
12 µA
+125ºC
All devices 4.5
4.8
4.8
11
µA
12 µA
12 µA
-40°C
+25°C
+85°C
VDD = 3.3V⁽⁴⁾
Regulator Disabled
5.0
14 µA
+125ºC
All devices 4.9
4.9
4.9
13 µA
13 µA
13 µA
-40°C
+25°C
+85°C
VDD = 5V⁽⁵⁾
Regulator Enabled
5.3
15 µA
+125ºC
Note 1:
2:
3:
4:
5:
6:
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in a high-impedance state and tied to VDD or VSS, and all features that add delta
current are disabled (such as WDT, SOSC oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in Active Operation mode are:
OSC1 = External square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
Voltage regulator disabled (ENVREG = 0, tied to VSS, RETEN (CONFIG1L<0>) = 1).
Voltage regulator enabled (ENVREG = 1, tied to VDD, SRETEN (WDTCON<4>) = 1 and RETEN (CONFIG1L<0>) = 0).
48 MHz, maximum frequency at +125ºC.
 2011 Microchip Technology Inc.
DS39960D-page 495