PIC18F86K22-I Datasheet, PDF (491/550 Pages) Microchip Technology – 64/80-Pin, High-Performance, 1-Mbit Enhanced Flash Microcontrollers

PIC18F87K22 FAMILY
31.2 DC Characteristics: Power-Down and Supply Current
PIC18F87K22 Family (Industrial/Extended) (Continued)
PIC18F87K22 Family
(Industrial/Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Device
Typ
Max Units
Conditions
Note
Supply Current (IDD) Cont.^(2,3)
All devices 130
390 µA
-40°C
130
390 µA
130
390 µA
+25°C
+85°C
VDD = 1.8V⁽⁴⁾
Regulator Disabled
250
500 µA
+125ºC
All devices 270
270
270
400
790 µA
790 µA
790 µA
900 µA
-40°C
+25°C
+85°C
+125ºC
VDD = 3.3V⁽⁴⁾
Regulator Disabled
FOSC = 1 MHZ
(PRI_RUN mode,
EC oscillator)
All devices 430
990 µA
-40°C
450
980 µA
460
980 µA
+25°C
+85°C
VDD = 5V⁽⁵⁾
Regulator Enabled
600
1300 µA
+125ºC
All devices 430
860 µA
-40°C
530
900 µA
490
880 µA
+25°C
+85°C
VDD = 1.8V⁽⁴⁾
Regulator Disabled
750
1600 µA
+125ºC
All devices
850
850
850
1150
1750 µA
1700 µA
1800 µA
2400 µA
-40°C
+25°C
+85°C
+125ºC
VDD = 3.3V⁽⁴⁾
Regulator Disabled
FOSC = 4 MHz
(PRI_RUN mode,
EC oscillator)
All devices 1.1
2.7 mA
-40°C
1.1
2.6 mA
1.1
2.6 mA
+25°C
+85°C
VDD = 5V⁽⁵⁾
Regulator Enabled
2.0
4.0 mA
+125ºC
All devices 12
19 mA
-40°C
12
12
13
All devices 13
13
13
19 mA
19 mA
22 mA
20 mA
20 mA
20 mA
+25°C
+85°C
+125ºC⁽⁶⁾
-40°C
+25°C
+85°C
VDD = 3.3V⁽⁴⁾
Regulator Disabled
VDD = 5V⁽⁴⁾
Regulator Enabled
FOSC = 64 MHZ
(PRI_RUN mode,
EC oscillator)
14
23 mA
+125ºC⁽⁶⁾
1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in a high-impedance state and tied to VDD or VSS, and all features that add delta
current are disabled (such as WDT, SOSC oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in Active Operation mode are:
OSC1 = External square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
3: Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
4: Voltage regulator disabled (ENVREG = 0, tied to VSS, RETEN (CONFIG1L<0>) = 1).
5: Voltage regulator enabled (ENVREG = 1, tied to VDD, SRETEN (WDTCON<4>) = 1 and RETEN (CONFIG1L<0>) = 0).
6: 48 MHz, maximum frequency at +125ºC.
 2011 Microchip Technology Inc.
DS39960D-page 491