PIC18F86K22-I Datasheet, PDF (493/550 Pages) Microchip Technology – 64/80-Pin, High-Performance, 1-Mbit Enhanced Flash Microcontrollers

PIC18F87K22 FAMILY
31.2 DC Characteristics: Power-Down and Supply Current
PIC18F87K22 Family (Industrial/Extended) (Continued)
PIC18F87K22 Family
(Industrial/Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Device
Typ
Max Units
Conditions
Note
Supply Current (IDD) Cont.^(2,3)
All devices 42
73 µA
-40°C
42
73 µA
43
74 µA
+25°C
+85°C
VDD = 1.8V⁽⁴⁾
Regulator Disabled
53
100 µA
+125ºC
All devices 110
110
110
130
190 µA
195 µA
195 µA
250 µA
-40°C
+25°C
+85°C
+125ºC
VDD = 3.3V⁽⁴⁾
Regulator Disabled
FOSC = 1 MHz
(PRI_IDLE mode,
EC oscillator)
All devices 280
450 µA
-40°C
290
440 µA
300
460 µA
+25°C
+85°C
VDD = 5V⁽⁵⁾
Regulator Enabled
330
500 µA
+125ºC
All devices 160
360 µA
-40°C
160
360 µA
170
370 µA
+25°C
+85°C
VDD = 1.8V⁽⁴⁾
Regulator Disabled
200
400 µA
+125ºC
All devices 330
340
340
370
650 µA
660 µA
660 µA
700 µA
-40°C
+25°C
+85°C
+125ºC
VDD = 3.3V⁽⁴⁾
Regulator Disabled
FOSC = 4 MHz
(PRI_IDLE mode,
EC oscillator)
All devices 510
900 µA
-40°C
520
950 µA
540
990 µA
+25°C
+85°C
VDD = 5V⁽⁵⁾
Regulator Enabled
600
1200 µA
+125ºC
All devices 4.7
9
mA
-40°C
4.8
4.8
5.2
All devices 5.1
5.1
5.2
9
mA
10 mA
12 mA
11 mA
11 mA
12 mA
+25°C
+85°C
+125ºC⁽⁶⁾
-40°C
+25°C
+85°C
VDD = 3.3V⁽⁴⁾
Regulator Disabled
VDD = 5V⁽⁵⁾
Regulator Enabled
FOSC = 64 MHz
(PRI_IDLE mode,
EC oscillator)
5.7
14 mA
+125ºC⁽⁶⁾
1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in a high-impedance state and tied to VDD or VSS, and all features that add delta
current are disabled (such as WDT, SOSC oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in Active Operation mode are:
OSC1 = External square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
3: Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
4: Voltage regulator disabled (ENVREG = 0, tied to VSS, RETEN (CONFIG1L<0>) = 1).
5: Voltage regulator enabled (ENVREG = 1, tied to VDD, SRETEN (WDTCON<4>) = 1 and RETEN (CONFIG1L<0>) = 0).
6: 48 MHz, maximum frequency at +125ºC.
 2011 Microchip Technology Inc.
DS39960D-page 493