PIC18F2450_08 Datasheet, PDF (135/324 Pages) Microchip Technology – 28/40/44-Pin, High-Performance, 12 MIPS, Enhanced Flash, USB Microcontrollers with nanoWatt Technology

TABLE 14-1:
VPO
0
0
1
1
VMO
0
1
0
1
DIFFERENTIAL OUTPUTS TO
TRANSCEIVER
Bus State
Single-Ended Zero
Differential ‘0’
Differential ‘1’
Illegal Condition
TABLE 14-2: SINGLE-ENDED INPUTS
FROM TRANSCEIVER
VP
VM
Bus State
0
0
0
1
1
0
1
1
Single-Ended Zero
Low Speed
High Speed
Error
The UOE signal toggles the state of the external
transceiver. This line is pulled low by the device to
enable the transmission of data from the SIE to an
external device.
14.2.2.3 Internal Pull-up Resistors
The PIC18F2450/4450 devices have built-in pull-up
resistors designed to meet the requirements for low-
speed and full-speed USB. The UPUEN bit (UCFG<4>)
enables the internal pull-ups. Figure 14-1 shows the
pull-ups and their control.
14.2.2.4 Pull-up Resistors
The PIC18F2450/4450 devices require an external
pull-up resistor to meet the requirements for low-speed
and full-speed USB. Either an external 3.3V supply or
the VUSB pin may be used to pull up D+ or D-. The pull-
up resistor must be 1.5 kΩ (±5%) as required by the
USB specifications. Figure 14-3 shows an example
with the VUSB pin.
FIGURE 14-3:
PIC^®
Microcontroller
VUSB
EXTERNAL CIRCUITRY
Host
Controller/HUB
1.5 kΩ
D+
D-
Note: The above setting shows a typical connection for a
full-speed configuration using an on-chip regulator
and an external pull-up resistor.
14.2.2.5 Ping-Pong Buffer Configuration
The usage of ping-pong buffers is configured using the
PPB1:PPB0 bits. Refer to Section 14.4.4 “Ping-Pong
Buffering” for a complete explanation of the ping-pong
buffers.
© 2008 Microchip Technology Inc.
PIC18F2450/4450
14.2.2.6 USB Output Enable Monitor
The USB OE monitor provides indication as to whether
the SIE is listening to the bus or actively driving the bus.
This is enabled by default when using an external
transceiver or when UCFG<6> = 1.
The USB OE monitoring is useful for initial system
debugging, as well as scope triggering during eye
pattern generation tests.
14.2.2.7 Eye Pattern Test Enable
An automatic eye pattern test can be generated by the
module when the UCFG<7> bit is set. The eye pattern
output will be observable based on module settings,
meaning that the user is first responsible for configuring
the SIE clock settings, pull-up resistor and Transceiver
mode. In addition, the module has to be enabled.
Once UTEYE is set, the module emulates a switch from
a receive to transmit state and will start transmitting a
J-K-J-K bit sequence (K-J-K-J for full speed). The
sequence will be repeated indefinitely while the Eye
Pattern Test mode is enabled.
Note that this bit should never be set while the module
is connected to an actual USB system. This test mode
is intended for board verification to aid with USB certi-
fication tests. It is intended to show a system developer
the noise integrity of the USB signals which can be
affected by board traces, impedance mismatches and
proximity to other system components. It does not
properly test the transition from a receive to a transmit
state. Although the eye pattern is not meant to replace
the more complex USB certification test, it should aid
during first order system debugging.
14.2.2.8 Internal Regulator
The PIC18F2450/4450 devices have a built-in 3.3V
regulator to provide power to the internal transceiver and
provide a source for the external pull-ups. An external
220 nF (±20%) capacitor is required for stability.
Note:
The drive from VUSB is sufficient to only
drive an external pull-up in addition to the
internal transceiver.
The regulator is disabled by default and can be enabled
through the VREGEN Configuration bit. When enabled,
the voltage is visible on pin VUSB. When the regulator
is disabled, a 3.3V source must be provided through
the VUSB pin for the internal transceiver. If the internal
transceiver is disabled, VUSB is not used.
Note 1: Do not enable the internal regulator if an
external regulator is connected to VUSB.
2: VDD must be greater than or equal to
VUSB at all times, even with the regulator
disabled.
DS39760D-page 133