English
Language : 

PIC16F872_06 Datasheet, PDF (126/168 Pages) Microchip Technology – 28-Pin, 8-Bit CMOS Flash Microcontroller with 10-Bit A/D
PIC16F872
14.4 DC Characteristics: PIC16F872 (Extended)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +125°C
Operating voltage VDD range as described in DC specification
(Section 14.1)
Param
No.
Sym
Characteristic
Min Typ† Max Units
Conditions
VIL Input Low Voltage
I/O ports:
D030
with TTL buffer
Vss
- 0.15VDD V For entire VDD range
D030A
Vss
- 0.8V V 4.5V ≤ VDD ≤ 5.5V
D031
with Schmitt Trigger buffer
Vss
- 0.2VDD V
D032
MCLR, OSC1 (in RC mode)
VSS
- 0.2VDD V
D033
OSC1 (in XT, HS and LP modes) VSS
- 0.3VDD V (Note1)
Ports RC3 and RC4:
D034
with Schmitt Trigger buffer
Vss
- 0.3VDD V For entire VDD range
D034A
with SMBus
-0.5
-
0.6
V for VDD = 4.5 to 5.5V
VIH Input High Voltage
I/O ports:
-
D040
with TTL buffer
2.0
-
VDD
V 4.5V ≤ VDD ≤ 5.5V
D040A
0.25VDD -
VDD
V For entire VDD range
+ 0.8V
D041
with Schmitt Trigger buffer 0.8VDD -
VDD
V For entire VDD range
D042
MCLR
0.8VDD -
VDD
V
D042A
OSC1 (XT, HS and LP modes) 0.7VDD -
VDD
V (Note1)
D043
OSC1 (in RC mode)
0.9VDD -
VDD
V
Ports RC3 and RC4:
D044
with Schmitt Trigger buffer 0.7VDD -
VDD
V For entire VDD range
D044A
with SMBus
1.4
-
5.5
V for VDD = 4.5 to 5.5V
D070A IPURB PORTB Weak Pull-up Current
50 300 500 μA VDD = 5V, VPIN = VSS,
IIL
Input Leakage Current(2, 3)
D060
I/O ports
-
-
±1
μA Vss ≤ VPIN ≤ VDD,
Pin at hi-impedance
D061
MCLR, RA4/T0CKI
-
-
±5
μA Vss ≤ VPIN ≤ VDD
D063
OSC1
-
-
±5
μA Vss ≤ VPIN ≤ VDD, XT, HS
and LP osc configuration
* These parameters are characterized but not tested.
† Data in "Typ" column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16F872 be driven with external clock in RC mode.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels
represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.
DS30221C-page 124
© 2006 Microchip Technology Inc.