English
Language : 

MC68HC705J1ACPE Datasheet, PDF (122/162 Pages) Freescale Semiconductor, Inc – Freescale Semiconductor, Inc.
◁
Freescale Semiconductor, Inc.
Electrical Specifications
10.8 3.3-Volt DC Electrical Characteristics
Characteristic(1)
Symbol Min
Typ(2)
Max Unit
Output voltage
ILoad = 10.0 µA
ILoad = –10.0 µA
Output high voltage
(ILoad = –0.2 mA) PA0–PA7, PB0–PB5
Output low voltage
(ILoad = 0.4 mA) PA0–PA3, PB0–PB5
(ILoad = 5.0 mA) PA4–PA7
Input high voltage
PA0–PA7, PB0–PB5, IRQ/VPP, RESET, OSC1
Input low voltage
PA0–PA7, PB0–PB5, IRQ/VPP, RESET, OSC1
Supply current
Run Mode(3)
Wait Mode(4)
Stop Mode(5)
25°C
–40 to 105°C
I/O ports hi-z leakage current
PA0–PA7, PB0–PB5 (without individual pulldown activated)
Input pulldown current
PA0–PA7, PB0–PB5 (with individual pulldown activated)
Input pullup current
RESET
Input current(6)
RESET, IRQ/VPP, OSC1
Capacitance
Ports (as inputs or outputs)
RESET, IRQ/VPP, OSC1, OSC2
Crystal/ceramic resonator oscillator mode internal resistor
OSC1 to OSC2(7)
VOL
VOH
VOH
VOL
VIH
VIL
IDD
IIL
IIL
IIL
IIn
COut
CIn
Rosc
—
VDD– 0.1
VDD – 0.3
—
0.7 × VDD
VSS
—
—
—
—
—
12
–10
—
—
—
1.0
—
—
—
—
—
—
1.2
0.25
0.1
1.0
0.1
30
–25
0.1
—
—
2.0
0.1
V
—
—
V
0.3
0.3
V
VDD
V
0.2 × VDD V
4.0
mA
1.5
mA
5
µA
10
µA
±1
µA
100
µA
–45
µA
±1
µA
12
pF
8
3.0
MΩ
1. VDD = 3.3 Vdc ± 10%, VSS = 0 Vdc, TA = –40°C to +105°C, unless otherwise noted
2. Typical values at midpoint of voltage range, 25°C only
3. Run mode IDD is measured using external square wave clock source (fosc = 2.0 MHz); all inputs 0.2 V from rail; no dc loads;
less than 50 pF on all outputs; CL = 20 pF on OSC2
4. Wait mode IDD: only timer system active. Wait mode is affected linearly by OSC2 capacitance. Wait mode is measured
with all ports configured as inputs; VIL = 0.2 V; VIH = VDD – 0.2 V. Wait mode IDD is measured using external square wave
clock source (fosc = 2.0 MHz); all inputs 0.2 V from rail; no dc loads; less than 50 pF on all outputs; CL = 20 pF on OSC2.
5. Stop mode IDD is measured with OSC1 = VSS. Stop mode IDD is measured with all ports configured as inputs; VIL = 0.2 V;
VIH = VDD – 0.2 V
6. Only input high current rated to +1 µA on RESET.
7. The Rosc value selected for RC oscillator versions of this device is unspecified. See Appendix C. MC68HSR705J1A for
additional information.
Technical Data
MC68HC705J1A — Rev. 4.0
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
 ▷