UG534 Datasheet, PDF (67/96 Pages) –

Table 1-30: VITA 57.1 FMC LPC Connections (Cont’d)
J63 FMC
LPC Pin
Schematic Net Name
U1 FPGA J63 FMC
Pin
LPC Pin
G21 FMC_LPC_LA20_P
P29
H20
G22 FMC_LPC_LA20_N
R29
H22
G24 FMC_LPC_LA22_P
N27
H23
G25 FMC_LPC_LA22_N
P27
H25
G27 FMC_LPC_LA25_P
P31
H26
G28 FMC_LPC_LA25_N
P30
H28
G30 FMC_LPC_LA29_P
N34
H29
G31 FMC_LPC_LA29_N
P34
H31
G33 FMC_LPC_LA31_P
M31
H32
G34 FMC_LPC_LA31_N
L31
H34
G36 FMC_LPC_LA33_P
K32
H35
G37 FMC_LPC_LA33_N
K31
H37
H38
Detailed Description
Schematic Net Name
FMC_LPC_LA15_N
FMC_LPC_LA19_P
FMC_LPC_LA19_N
FMC_LPC_LA21_P
FMC_LPC_LA21_N
FMC_LPC_LA24_P
FMC_LPC_LA24_N
FMC_LPC_LA28_P
FMC_LPC_LA28_N
FMC_LPC_LA30_P
FMC_LPC_LA30_N
FMC_LPC_LA32_P
FMC_LPC_LA32_N
U1 FPGA
Pin
B32
M30
N30
R26
T26
N32
P32
N33
M33
M26
M27
N25
M25
References
See the data sheet for the ROHS compliant FMC HPC Samtec SEARAY connector (carrier
side socket ASP-134486-01; module side plug ASP-134488-01), and the high-speed
characterization report for this connector system on the Samtec website. [Ref 32]
21. Power Management
AC Adapter and Input Power Jack/Switch
The ML605 is powered from a 12V source that is connected through a 6-pin (2X3) right-
angle Mini-Fit type connector J60. The AC-to-DC power supply included in the kit has a
mating 6-pin plug.
When the ML605 is installed into a table top or tower PC's PCIe slot, the ML605 is typically
powered from the PC ATX power supply. One of the ATX hard disk type 4-pin power
connectors is plugged into ML605 connector J25. The ML605 can be powered with the AC
power adapter even when plugged into a PC PCIe motherboard slot; however, users are
cautioned not to also connect an ATX 4-pin power connector to J25. See the caution notes
below and in Figure 1-23, page 55.
Caution! DO NOT plug a PC ATX power supply 6-pin connector into ML605 connector J60.
The ATX 6-pin connector has a different pinout than ML605 J60, and connecting the ATX 6-pin
connector will damage the ML605 and void the board warranty.
Caution! DO NOT apply power to J60 and the 4-pin ATX disk drive connector J25 at the same
time as this will damage the ML605 board. Refer to Figure 1-23, page 55 for details.
The ML605 power can be turned on or off through the board mounted slide switch SW2.
When the switch is in the on position, a green LED (DS25) is illuminated.
ML605 Hardware User Guide
www.xilinx.com
67
UG534 (v1.8) October 2, 2012