UG534 Datasheet, PDF (36/96 Pages) –

Chapter 1: ML605 Evaluation Board
Table 1-8: PCIe Edge Connector Connections (Cont’d)
U1 FPGA
Pin
Schematic Net Name
P1 PCIe Edge Connector
Pin Number Pin Name
Description
AA3
AA4
P6
P5
V6
V5
U14.6
PCIE_RX7_P
PCIE_RX7_N
PCIE_100M_MGT0_P
PCIE_100M_MGT0_N
PCIE_250M_MGT1_P
PCIE_250M_MGT1_N
PCIE_CLK_QO_P
U14.7
PCIE_CLK_QO_N
J42.2,4,6
PCIE_PRSNT_B
B45
B46
U14.16
U14.15
U9.18
U9.17
A13
A14
A1
AD22
PCIE_WAKE_B
B11
AE13
PCIE_PERST_B
A11
PETp7
PETn7
Q0
NQ0
Q
NQ
REFCLK+
REFCLK-
PRSNT#1
WAKE#
PERST
Integrated Endpoint block
receive pair
Sourced from U14 ICS854104
clock driver
Sourced from U9 ICS874001
clock multiplier/driver
Integrated Endpoint block
differential clock pair from PCIe
edge connector
J42 Lane Size Select jumper
Integrated Endpoint block wake
signal, not connected on ML605
board
Integrated Endpoint block reset
signal
Notes:
1. PCIE_TXn_P/N pairs are capacitively coupled to FPGA
2. PCIE_100M_MGT0_P/N pairs are capacitively coupled to FPGA
3. PCIE_250M_MGT1_P/N pairs are capacitively coupled to FPGA
4. PCIE_PERST_B is level-shifted by U32
5. For ML605, access is through MGT Banks 114 and 115
Package
Placement
GTXE1_X0Y8
IBUF_
GTXE1_X0Y6
IBUF_
GTXE1_X0Y4
The PCIe interface obtains its power from the DC power supply provided with the ML605
or through the 12V ATX power supply connector. The PCIe edge connector is not used for
any power connections.
The board can be powered by one of two 12V sources; J60, a 6-pin (2x3) molex-type
connector and J25, a 4-pin (inline) ATX disk drive type connector.
The 6-pin molex-type connector provides 60W (12V @ 5A) from the AC power adapter
provided with the board while the 4-pin ATX disk drive connector is provided for users
who want to power their board while it is installed inside a PC chassis.
For applications requiring additional power, such as the use of expansion cards drawing
significant power, a larger AC adapter might be required. If a different AC adapter is used,
its load regulation should be better than ±10%.
ML605 power switch SW2 turns the board on and off by controlling the 12V supply to the
board.
Caution! Never apply power to the power brick connector (J60) and the 4-pin ATX disk drive
connector (J25) at the same time as this will result in damage to the board. See Figure 1-23,
page 55. Never connect an auxiliary PCIe 6-pin molex power connector to J60 6-pin molex on
the ML605 board as this could result in damage to the PCIe motherboard and/or ML605 board.
The 6-pin molex connector is marked with a no PCIe power label to warn users of the potential
hazard.
36
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.8) October 2, 2012