M30218 Datasheet, PDF (76/179 Pages) Mitsubishi Electric Semiconductor – M30218 Group

Timer A
Mitsubishi microcomputers
M30218 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
(2) Event counter mode
In this mode, the timer counts an external signal or an internal timer’s overflow. Timers A0 and A1 can
count a single-phase external signal. Timers A2, A3, and A4 can count a single-phase and a two-phase
external signal. Table FB-2 lists timer specifications when counting a single-phase external signal. Fig-
ure FB-7 shows the timer Ai mode register in event counter mode.
Table FB-3 lists timer specifications when counting a two-phase external signal. Figure FB-8 shows the
timer Ai mode register in event counter mode.
Table FB-2. Timer specifications in event counter mode (when not processing two-phase pulse signal)
Item
Count source
Count operation
Divide ratio
Count start condition
Count stop condition
Specification
•External signals input to TAiIN pin (effective edge can be selected by software)
•TB2 overflow, TAj overflow
•Up count or down count can be selected by external signal or software
•When the timer overflows or underflows, the reload register's content is reloaded
and the timer starts over again.(Note)
1/ (FFFF16 - n + 1) for up count
1/ (n + 1) for down count
n : Set value
Count start flag is set (= 1)
Count start flag is reset (= 0)
Interrupt request generation timing The timer overflows or underflows
TAiIN pin function
Programmable I/O port or count source input
TAiOUT pin function
Programmable I/O port, pulse output, or up/down count select input
Read from timer
Write to timer
Select function
Count value can be read out by reading timer Ai register
•When counting stopped
When a value is written to timer Ai register, it is written to both reload register and counter
•When counting in progress
When a value is written to timer Ai register, it is written to only reload register
(Transferred to counter at next reload time)
•Free-run count function
Even when the timer overflows or underflows, the reload register content is not reloaded to it
•Pulse output function
Each time the timer overflows or underflows, the TAiOUT pin’s polarity is reversed
Note: This does not apply when the free-run function is selected.
Timer Ai mode register
b7 b6 b5 b4 b3 b2 b1 b0
0
01
Symbol
TAiMR(i = 0, 1)
Address
When reset
039616, 039716
0016
Bit symbol
TMOD0
TMOD1
MR0
MR1
Bit name
Function
RW
Operation mode select bit ^{b1 b0}
0 1 : Event counter mode (Note 1)
Pulse output function
select bit
0 : Pulse is not output
(TAiOUT pin is a normal port pin)
1 : Pulse is output (Note 2)
(TAiOUT pin is a pulse output pin)
Count polarity
select bit (Note 3)
0 : Counts external signal's falling edge
1 : Counts external signal's rising edge
MR2
MR3
TCK0
Up/down switching
cause select bit
0 : Up/down flag's content
1 : TAiOUT pin's input signal (Note 4)
0 (Must always be fixed to “0” in event counter mode)
Count operation type select 0 : Reload type
bit
1 : Free-run type
TCK1
Invalid in event counter mode
Can be “0” or “1”
Note 1: In event counter mode, the count source is selected by the event / trigger select bit
(addresses 038216 and 038316).
Note 2: The settings of the corresponding port register and port direction register are invalid.
Note 3: Valid only when counting an external signal.
Note 4: When an “L” signal is input to the TAiOUT pin, the downcount is activated. When “H”,
the upcount is activated. Set the corresponding port direction register to “0”.
Figure FB-7. Timer Ai mode register in event counter mode
75