M30218 Datasheet, PDF (140/179 Pages) Mitsubishi Electric Semiconductor – M30218 Group

Electrical characteristics
Mitsubishi microcomputers
M30218 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Table Z-3. Recommended operating conditions (referenced to VCC = 2.7V to 5.5V at Ta = – 20 to
85^oC unless otherwise specified) (Note 6)
Symbol
I OH (peak)
I OH (peak)
I OH (peak)
I OH (peak)
I OL (peak)
I OL (peak)
I OH (avg)
I OH (avg)
I OH (avg)
I OH (avg)
I OL (avg)
I OL (avg)
I OH (peak)
I OH (peak)
I OL (peak)
I OH (avg)
I OH (avg)
I OL (avg)
f (XIN)
Parameter
HIGH total peak output P00 to P07, P50 to P57, P60 to P67
current (Note 1)
HIGH total peak output P10 to P17, P20 to P27, P30 to P37, P40 to P43
current (Note 1)
HIGH total peak output P44 to P47, P70 to P77, P80 to P85
current (Note 1)
HIGH total peak output P86, P87, P90 to P97, P100 to P107
current (Note 1)
LOW total peak output
current (Note 1)
P44 to P47, P70 to P77, P80 to P85
LOW total peak output
current (Note 1)
HIGH total average
output current (Note 1)
P86, P87, P90 to P97, P100 to P107
P00 to P07, P50 to P57, P60 to P67
HIGH total average
output current (Note 1)
P10 to P17, P20 to P27, P30 to P37, P40 to P43
HIGH total average
output current (Note 1)
P44 to P47, P70 to P77, P80 to P85
HIGH total average
output current (Note 1)
P86, P87, P90 to P97, P100 to P107
LOW total average
output current (Note 1)
P44 to P47, P70 to P77, P80 to P85
LOW total average
output current (Note 1)
P86, P87, P90 to P97, P100 to P107
HIGH peak output
current (Note 2)
HIGH peak output
current (Note 2)
P00 to P07, P10 to P17, P20 to P27,P30 to P37,
P40 to P43, P50 to P57, P60 to P67
P44 to P47, P70 to P77, P80 to P87
P90 to P97, P100 to P107
LOW peak output
current (Note 2)
P44 to P47, P70 to P77, P80 to P87
P90 to P97, P100 to P107
HIGH average output
current (Note 3)
P00 to P07, P10 to P17, P20 to P27,P30 to P37,
P40 to P43, P50 to P57, P60 to P67
HIGH average output
current (Note 3)
P44 to P47, P70 to P77, P80 to P87
P90 to P97, P100 to P107
LOW average output
current (Note 3)
P44 to P47, P70 to P77, P80 to P87
P90 to P97, P100 to P107
Vcc=4.0V to 5.5V
Main clock input oscillation frequency (Note 4, 7)
Vcc=2.7V to 4.0V
Standard
Min Typ. Max. ^Unit
-240 mA
-240 mA
-80 mA
-80 mA
80 mA
80 mA
-120 mA
-120 mA
-40 mA
-40 mA
40 mA
40 mA
-40 mA
-10 mA
10 mA
-18 mA
-5 mA
5 mA
0
10 MHz
0
5 X Vcc-10 MHz
f (XcIN)
Sub clock oscillation frequency (Note 4, 5)
32.768
50 kHz
Note 1: The total output current is the sum of all the currents through the applicable ports. The total
average value measured over 100ms. The total peak current is the peak of all the currents.
Note 2: The peak output current is the peak current flowing in each port.
Note 3: The average output current in an average value measured over 100ms.
Note 4: When the oscillating frequency has a duty cycle of 50 %.
Note 5: When using the microcomputer in low-speed mode, set the sub-clock input oscillation frequency
on condition that f(XCIN) < f(XIN) / 3.
Note 6: VCC=4.0V to 5.5V in flash memory version.
Note 7: Relationship between main clock oscillation frequency and supply voltage.
Main clock input oscillation frequency
(No wait)
10.0
5 X VCC-10.000MHZ
3.5
0.0
2.7
4.0
5.5
Flash memory version
Supply voltage[V] (BCLK: no division)
139