M30218 Datasheet, PDF (147/179 Pages) Mitsubishi Electric Semiconductor – M30218 Group

Mitsubishi microcomputers
M30218 Group
Electrical characteristics(VCC=3V, only mask ROM version) _{SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER}
Table Z-20. Electrical characteristics (referenced to VCC = 3V, VSS = 0V at Ta = 25^oC,
f(XIN) =5MHZ unless otherwise specified)
Symbol
VOH
VOH
VOH
VOL
VOL
VT+-VT-
Parameter
Measuring condition
HIGH output ^{P00 to P07,P10 to P17,P20 to P27,}
voltage
P30 to P37,P40 to P43,P50 to P57,
P60 to P67
HIGH output ^{P44 to P47,P70 to P77,P80 to P87,}
voltage
P90 to P97,P100 to P107
IOH= - 18mA
IOH= - 5mA
IOH= - 1mA
HIGH output
voltage
XOUT
HIGH POWER
LOW POWER
IOH= - 0.1mA
IOH= - 50µA
LOW output
voltage
LOW output
voltage
P44 to P47,P70 to P77,P80 to P87,
P90 to P97,P100 to P107
XOUT
HIGH POWER
LOW POWER
IOL=1mA
IOL=0.1mA
IOL=50µA
Hysteresis
TA0IN to TA4IN,TB0IN to TB2IN,
INT0 to INT5, CTS0, CTS1,
CLK0,CLK1,SRDY2IN,SBSY2IN,
SIN2,SCLK21,SCLK22
RTS0,RTS1
Standard
Min. Typ. Max. ^Unit
1.5
V
2.5
2.5
V
2.5
V
2.5
0.5 V
0.5
V
0.5
0.2
0.8 V
VT+-VT-
IIH
IIH
II L
II L
Hysteresis
HIGH input
current
LOW input
current
RESET
P44 to P47,P70 to P77,P80 to P87,
P90 to P97,P100 to P107,
VI=3V
XIN, RESET, CNVss
P30 to P37,P40 to P43(Note 1)
VI=3V
P44 to P47,P70 to P77,P80 to P87,
P90 to P97,P100 to P107,
XIN, RESET, CNVss
VI=0V
P30 to P37,P40 to P43(Note 1)
VI=0V
0.2
1.8 V
4.0 µA
4.0 µA
- 4.0 µA
- 4.0 µA
RPULLUP
Pull-up
resistance
P44 to P47,P70 to P77,
P80 to P87,P90 to P97,
P100 to P107
VI=0V
66.0 120.0 500.0 kΩ
RPULLD
Pull-down
resistance
P00 to P07,P10 to P17,
P50 to P57,P60 to P67
VEE=VCC - 48V,VOL=VCC
Output transistors “off”
68 80 120
kΩ
ILEAK
Output leak
current
P00 to P07,P10 to P17,
P20 to P27,P30 to P37,
P40 to P44,P50 to P57,
P60 to P67
VEE=VCC - 48V,VOL=VCC - 48V
Output transistors “off”
- 10
µA
RfXIN
Feedback resistance XIN
RfXCIN
Feedback resistance XCIN
VRAM
RAM retention voltage
When clock is stopped
The output
pins are open
and other
pins are VSS
f(XIN)=5MHz
Square wave, no division
f(XIN)=5MHz
Square wave, 8 division
f(XCIN)=32kHz
Icc
Power supply current (Note 3)
Square wave
f(XCIN)=32kHz
When a WAITinstruction
is executed.
Oscillation capacity High (Note2)
f(XCIN)=32kHz
When a WAIT instruction
is executed.
Oscillation capacity Low (Note2)
Ta=25 C
when clock is stopped
Ta=85 C
when clock is stopped
Note 1: Except when reading ports P3, P40 to P43.
Note 2: With one timer operated using fC32.
Note 3: This contains an electric current to flow into AVCC pin.
3.0
MΩ
10.0
MΩ
2.0
V
6.0 15.0 mA
1.6
mA
50.0
µA
2.8
µA
0.9
µA
1.0
µA
20.0
146
VCC=3V