M30218 Datasheet, PDF (141/179 Pages) Mitsubishi Electric Semiconductor – M30218 Group

Electrical characteristics (VCC=5V)
Mitsubishi microcomputers
M30218 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Table Z-4. Electrical characteristics (referenced to VCC = 5V, VSS = 0V at Ta = 25^oC,
f(XIN) =10MHZ unless otherwise specified)
Symbol
Parameter
Measuring condition
VOH
VOH
VOH
VOL
VOL
VT+-VT-
HIGH output ^{P00 to P07,P10 to P17,P20 to P27,}
voltage
P30 to P37,P40 to P43,P50 to P57,
P60 to P67
HIGH output ^{P44 to P47,P70 to P77,P80 to P87,}
voltage
P90 to P97,P100 to P107
IOH= - 18mA
IOH= - 5mA
IOH= - 5mA
HIGH output
voltage
XOUT
HIGH POWER
LOW POWER
IOH= - 1mA
IOH= - 0.5mA
LOW output P44 to P47,P70 to P77,P80 to P87,
voltage
P90 to P97,P100 to P107
LOW output XOUT
voltage
HIGH POWER
LOW POWER
IOL=5mA
IOL=1mA
IOL=0.5mA
Hysteresis
TA0IN to TA4IN,TB0IN to TB2IN,
INT0 to INT5, CTS0, CTS1,
CLK0,CLK1,SRDY2IN,SBSY2IN,
SIN2,SCLK21,SCLK22,RxD0,
RxD1
Standard
Min. Typ. Max. ^Unit
3.5
V
4.5
3.0
V
3.0
V
3.0
2.0 V
2.0
V
2.0
0.2
0.8 V
VT+-VT-
II H
II H
IIL
II L
Hysteresis
HIGH input
current
RESET
P44 to P47,P70 to P77,P80 to P87,
P90 to P97,P100 to P107,
XIN, RESET, CNVss
VI=5V
P30 to P37,P40 to P43(Note 1)
VI=5V
LOW input
current
P44 to P47,P70 to P77,P80 to P87,
P90 to P97,P100 to P107,
XIN, RESET, CNVss
VI=0V
P30 to P37,P40 to P43(Note1)
VI=0V
0.2
1.8 V
5.0 µA
5.0 µA
- 5.0 µA
- 5.0 µA
RPULLUP
Pull-up
resistance
P44 to P47,P70 to P77,
P80 to P87,P90 to P97,
P100 to P107
VI=0V
30.0 50.0 167.0 kΩ
RPULLD
Pull-down
resistance
P00 to P07,P10 to P17,
P50 to P57,P60 to P67
VEE=VCC - 48V,VOL=VCC
Output transistors “off”
68 80 120
kΩ
ILEAK
Output leak
current
P00 to P07,P10 to P17,
P20 to P27,P30 to P37,
P40 to P44,P50 to P57,
P60 to P67
VEE=VCC - 48V,VOL=VCC - 48V
Output transistors “off”
- 10
µA
RfXIN
Feedback resistance XIN
1.0
MΩ
RfXCIN
Feedback resistance XCIN
6.0
MΩ
VRAM
RAM retention voltage
When clock is stopped
2.0
V
The output
pins are open
and other
pins are VSS
f(XIN)=10MHz
Square wave, no division
f(XIN)=10MHz
Square wave, 8 division
19.0 38.0 mA
4.2
mA
Icc
Power supply current (Note 3)
f(XCIN)=32kHz
Square wave (Note2)
90.0
µA
f(XCIN)=32kHz
4.0
µA
When a WAIT instruction is executed
(Note2)
Ta=25 C
when clock is stopped
Ta=85 C
when clock is stopped
1.0
µA
20.0
Note 1: Except when reading ports P3, P40 to P43.
Note 2: Fixed XCIN-XCOUT drive capacity select bit to “HIGH” and XIN pin to “H” level.
Note 3: This contains an electric current to flow into AVCC pin.
VCC=5V
140