RX113_16 Datasheet, PDF (63/131 Pages) Renesas Technology Corp – 32 MHz, 32-bit RX MCUs, 50 DMIPS, up to 512 Kbytes of flash memory

RX113 Group
5. Electrical Characteristics
Table 5.10 DC Characteristics (8) (2/2)
Conditions: 1.8 V ≤ VCC = VCC_USB ≤ 3.6 V, 1.8 V ≤ AVCC0 ≤ 3.6 V, VSS = AVSS0 = VSS_USB = 0 V, T_a = –40 to +105°C
Item
Symbol Min.
Typ.*⁷
Max.
Unit
Test
Conditions
USB operating During USB communication operation under the
current*³
following settings and conditions
I_USBH*¹ —
4.3
(VCC)
— mA
 Host controller operation is set to full-speed mode
0.9
Bulk OUT transfer (64 bytes) × 1,
(VCC_USB)*³
bulk IN transfer (64 bytes) × 1
 Connect peripheral devices via a 1-meter USB
cable from the USB port.
During USB communication operation under the
following settings and conditions
I_USBF*¹ —
3.6
(VCC)
— mA
 Function controller operation is set to full-speed
1.1
mode
(VCC_USB)*³
Bulk OUT transfer (64 bytes) × 1,
bulk IN transfer (64 bytes) × 1
 Connect the host device via a 1-meter USB cable
from the USB port.
During suspended state under the following setting
and conditions
I_SUSP*² —
0.35
(VCC)
— μA
 Function controller operation is set to full-speed
170
mode (pull up the USB0_DP pin)
(VCC_USB)*³
 Software standby mode
 Connect the host device via a 1-meter USB cable
from the USB port.
CTSU
operating
current
During measurement (CPU is in sleep mode)
Base clock: 2 MHz
Pin capacity: 50 pF
I_CTSU
—
150
— μA
Note 1. Current consumed only by the USB module.
Note 2. Includes the current supplied from the pull-up resistor of the USB0_DP pin to the pull-down resistor of the host device, in
addition to the current consumed by this MCU during the suspended state.
Note 3. Current consumed by the power supplies (VCC and VCC_USB).
Note 4. Current consumed only by the comparator B module.
Note 5. Current consumed only by the LCD module. Current when the LCD panel is not connected.
Note 6. Current consumed by the power supply (VCC).
Note 7. When VCC = AVCC0 = VCC_USB = 3.3 V.
Note 8. It does not include the current that flows through external divider resistors.
Table 5.11 DC Characteristics (9)
Conditions: 1.8 V ≤ VCC = VCC_USB ≤ 3.6 V, 1.8 V ≤ AVCC0 ≤ 3.6 V, VSS = AVSS0 = VSS_USB = 0 V, T_a = –40 to +105°C
Item
Symbol
Min.
Typ.
Max.
Unit
Test Conditions
RAM standby voltage
V_RAM
1.8
—
—
V
Table 5.12 DC Characteristics (10)
Conditions: 0 V ≤ VCC = VCC_USB ≤ 3.6 V, VSS = AVSS0 = VSS_USB = 0 V, T_a = –40 to +105°C
Item
Symbol Min. Typ. Max. Unit
Power-on VCC At normal startup*¹
rising gradient _{During fast startup time*2}
SrVCC 0.02 —
0.02 —
20 ms/V
2
Voltage monitoring 1 reset enabled at startup
*^3, *⁴
0.02 —
—
Test Conditions
Note:
Note 1.
Note 2.
Note 3.
Note 4.
When powering on AVCC0 and VCC, power them on at the same time or VCC first.
When OFS1.(STUPLVD1REN, FASTSTUP) = 11b.
When OFS1.(STUPLVD1REN, FASTSTUP) = 10b.
When OFS1.STUPLVD1REN = 0.
Turn on the power supply voltage according to the normal startup rising gradient because the register settings set by OFS1 are
not read in boot mode.
R01DS0216EJ0110 Rev.1.10
Mar 31, 2016
Page 63 of 131