PIC24FJ256GA110_10 Datasheet, PDF (279/330 Pages) Microchip Technology – 64/80/100-Pin, 16-Bit, General Purpose Flash Microcontrollers with Peripheral Pin Select

PIC24FJ256GA110 FAMILY
TABLE 28-7: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS (CONTINUED)
DC CHARACTERISTICS
Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Param
No.
Sym
Characteristic
Min
Typ⁽¹⁾ Max Units
Conditions
IIL Input Leakage Current^(2,3)
DI50
I/O Ports
—
—
+1
A VSS  VPIN  VDD,
Pin at high-impedance
DI51
Analog Input Pins
—
—
+1
A VSS  VPIN  VDD,
Pin at high-impedance
DI55
MCLR
—
—
+1
A VSS VPIN VDD
DI56
OSC1
—
—
+1
A VSS VPIN VDD,
XT and HS modes
Note 1:
2:
3:
4:
5:
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only
and are not tested.
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltages.
Negative current is defined as current sourced by the pin.
Refer to Table 1-4 for I/O pins buffer types.
VIH requirements are met when internal pull-ups are enabled.
TABLE 28-8: DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS
DC CHARACTERISTICS
Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Param
No.
Sym
Characteristic
Min
Typ⁽¹⁾ Max Units
Conditions
VOL Output Low Voltage
DO10
I/O Ports
—
—
0.4
V IOL = 8.5 mA, VDD = 3.6V
—
—
0.4
V IOL = 6.0 mA, VDD = 2.0V
DO16
OSC2/CLKO
—
—
0.4
V IOL = 8.5 mA, VDD = 3.6V
—
—
0.4
V IOL = 6.0 mA, VDD = 2.0V
VOH Output High Voltage
DO20
I/O Ports
3.0
—
—
V IOH = -3.0 mA, VDD = 3.6V
2.4
—
—
V IOH = -6.0 mA, VDD = 3.6V
1.65
—
—
V IOH = -1.0 mA, VDD = 2.0V
1.4
—
—
V IOH = -3.0 mA, VDD = 2.0V
DO26
OSC2/CLKO
2.4
—
—
V IOH = -6.0 mA, VDD = 3.6V
1.4
—
—
V IOH = -3.0 mA, VDD = 2.0V
Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only
and are not tested.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels
represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.
4: Refer to Table 1-4 for I/O pins buffer types.
5: VIH requirements are met when internal pull-ups are enabled.
 2010 Microchip Technology Inc.
DS39905E-page 279