MSP430F677X1_16 Datasheet, PDF (64/162 Pages) Texas Instruments – Polyphase Metering SoCs

MSP430F677x1, MSP430F676x1, MSP430F674x1
SLAS815C – NOVEMBER 2012 – REVISED DECEMBER 2013
www.ti.com
Outputs – General Purpose I/O (Full Drive Strength)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
V_OH High-level output voltage
V_OL Low-level output voltage
TEST CONDITIONS
I_(OHmax) = –3 mA ⁽¹⁾
I_(OHmax) = –10 mA⁽¹⁾
I_(OHmax) = –5 mA⁽¹⁾
I_(OHmax) = –15 mA⁽¹⁾
I_(OLmax) = 3 mA ⁽²⁾
I_(OLmax) = 10 mA ⁽³⁾
I_(OLmax) = 5 mA ⁽²⁾
I_(OLmax) = 15 mA⁽³⁾
V_CC
1.8 V
3V
1.8 V
3V
MIN
MAX UNIT
1.55
1.80
1.20
1.80
V
2.75
3.00
2.40
3.00
0.00
0.25
0.00
0.60
V
0.00
0.25
0.00
0.60
(1) The maximum total current, I_(OHmax), for all outputs combined should not exceed ±20 mA to hold the maximum voltage drop specified.
See Recommended Operating Conditions for more details.
(2) The maximum total current, I_(OLmax), for all outputs combined should not exceed ±48 mA to hold the maximum voltage drop specified.
(3) The maximum total current, I_(OLmax), for all outputs combined should not exceed ±100 mA to hold the maximum voltage drop specified.
Outputs – General Purpose I/O (Reduced Drive Strength)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)⁽¹⁾
PARAMETER
V_OH High-level output voltage
V_OL Low-level output voltage
TEST CONDITIONS
I_(OHmax) = –1 mA ⁽²⁾
I_(OHmax) = –3 mA⁽²⁾
I_(OHmax) = –2 mA⁽²⁾
I_(OHmax) = –6 mA⁽²⁾
I_(OLmax) = 1 mA ⁽³⁾
I_(OLmax) = 3 mA ⁽⁴⁾
I_(OLmax) = 2 mA ⁽³⁾
I_(OLmax) = 6 mA ⁽⁴⁾
V_CC
1.8 V
MIN
1.55
1.20
2.75
3V
2.40
0.00
1.8 V
0.00
0.00
3V
0.00
MAX
1.80
1.80
3.00
3.00
0.25
0.60
0.25
0.60
UNIT
V
V
(1) Selecting reduced drive strength may reduce EMI.
(2) The maximum total current, I_(OHmax), for all outputs combined should not exceed ±20 mA to hold the maximum voltage drop specified.
See Recommended Operating Conditions for more details.
(3) The maximum total current, I_(OLmax), for all outputs combined, should not exceed ±48 mA to hold the maximum voltage drop specified.
(4) The maximum total current, I_(OLmax), for all outputs combined, should not exceed ±100 mA to hold the maximum voltage drop specified.
Output Frequency – General Purpose I/O
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
f_Px.y
Port output frequency (with load)
TEST CONDITIONS
MIN
(1) (2)_{VCC = 1.8 V,}
PMMCOREVx = 0
V_CC = 3 V,
PMMCOREVx = 3
f_{Port_CLK} Clock output frequency
ACLK
SMCLK
MCLK
C_L = 20 pF⁽²⁾
V_CC = 1.8 V,
PMMCOREVx = 0
V_CC = 3 V,
PMMCOREVx = 3
MAX UNIT
16
MHz
25
16
MHz
25
(1) A resistive divider with 2 × R1 between V_CC and V_SS is used as load. The output is connected to the center tap of the divider. For full
drive strength, R1 = 550 Ω. For reduced drive strength, R1 = 1.6 kΩ. C_L = 20 pF is connected to the output to V_SS.
(2) The output voltage reaches at least 10% and 90% V_CC at the specified toggle frequency.
64
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated