MSP430F677X1_16 Datasheet, PDF (61/162 Pages) Texas Instruments – Polyphase Metering SoCs

MSP430F677x1, MSP430F676x1, MSP430F674x1
www.ti.com
SLAS815C – NOVEMBER 2012 – REVISED DECEMBER 2013
Low-Power Mode Supply Currents (Into V_CC) Excluding External Current
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)⁽¹⁾⁽²⁾
PARAMETER
Temperature (T_A)
V_CC
PMMCOREVx
-40°C
25°C
85°C
UNIT
TYP MAX TYP MAX TYP MAX
I_LPM0,1MHz
Low-power mode 0^{(3) (4)}
2.2 V
3V
0
3
70
81
75
86
µA
87
105
100
130
I_LPM2
Low-power mode 2^{(5) (4)}
2.2 V
3V
0
3
5.9
6.7
6.5
12.5
µA
7.3
18 13.8
30
0
1.50
2.0
7.8
I_LPM3,XT1LF
Low-power mode 3, crystal
mode ^{(6) (4)}
2.2 V
1
2
1.65
1.80
2.2
2.4
8.3
µA
8.6
3
1.84
2.4
8.6
0
2.0
2.5
8.5
I_LPM3,XT1LF
Low-power mode 3, crystal
mode ^{(6) (4)}
3V
1
2
2.1
2.3
2.7
2.9
9.0
µA
9.3
3
2.3
2.9
9.3
25
0
1.3
1.7
7.5
I_LPM3,VLO
Low-power mode 3,
VLO mode^{(7) (4)}
3V
1
2
1.3
1.4
1.8
1.9
7.9
µA
8.2
3
1.4
1.9
8.2 25.0
0
1.2
1.6
7.4
I_LPM4
Low-power mode 4^{(8) (4)}
3V
1
2
1.2
1.3
1.7
1.7
7.8
µA
7.9
3
1.3
1.7
8.0 23.0
I_LPM3.5
I_LPM4.5
Low-power mode 3.5, RTC
active on AUXVCC3⁽⁹⁾
Low-power mode 4.5⁽¹⁰⁾
2.2V
3.0V
3.0V
0.7
0.9
1.4
µA
1.0
1.2
1.5
1.8
3.0
0.6
0.7
1.0
1.2
2.0 µA
(1) All inputs are tied to 0 V or to V_CC. Outputs do not source or sink any current.
(2) The currents are characterized with a Micro Crystal MS1V-T1K crystal with a load capacitance of 12.5 pF. The internal and external load
capacitance are chosen to closely match the required 12.5 pF.
(3) Current for watchdog timer clocked by SMCLK included. ACLK = low frequency crystal operation (XTS = 0, XT1DRIVEx = 0).
CPUOFF = 1, SCG0 = 0, SCG1 = 0, OSCOFF = 0 (LPM0); f_ACLK = 32768 Hz, f_MCLK = 0 MHz, f_SMCLK = f_DCO = 1 MHz
(4) Current for brownout, high side supervisor (SVS_H) normal mode included. Low side supervisor and monitors disabled (SVS_L, SVM_L).
High side monitor disabled (SVM_H). RAM retention enabled.
(5) Current for watchdog timer and RTC clocked by ACLK included. ACLK = low frequency crystal operation (XTS = 0, XT1DRIVEx = 0).
CPUOFF = 1, SCG0 = 0, SCG1 = 1, OSCOFF = 0 (LPM2); f_ACLK = 32768 Hz, f_MCLK = 0 MHz, f_SMCLK = f_DCO = 0 MHz; DCO setting
= 1 MHz operation, DCO bias generator enabled.
(6) Current for watchdog timer and RTC clocked by low frequency clock included. ACLK = low frequency crystal operation (XTS = 0,
XT1DRIVEx = 0).
CPUOFF = 1, SCG0 = 1, SCG1 = 1, OSCOFF = 0 (LPM3); f_ACLK = 32768 Hz, f_MCLK = f_SMCLK = f_DCO = 0 MHz
(7) Current for watchdog timer and RTC clocked by low frequency clock included. ACLK = VLO.
CPUOFF = 1, SCG0 = 1, SCG1 = 1, OSCOFF = 0 (LPM3); f_ACLK = f_VLO, f_MCLK = f_SMCLK = f_DCO = 0 MHz
(8) CPUOFF = 1, SCG0 = 1, SCG1 = 1, OSCOFF = 1 (LPM4); f_DCO = f_ACLK = f_MCLK = f_SMCLK = 0 MHz
(9) f_DCO = f_MCLK = f_SMCLK = 0 MHz, f_ACLK = 32768 Hz, PMMREGOFF = 1, RTC active on AUXVCC3 supply
(10) f_DCO = f_MCLK = f_SMCLK = 0 MHz, f_ACLK = 0 Hz, PMMREGOFF = 1
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
61