LM3S2776 Datasheet, PDF (357/785 Pages) Texas Instruments – Stellaris® LM3S2776 Microcontroller

Stellaris® LM3S2776 Microcontroller
These four pins default to JTAG/SWD functionality. Because of this, the default reset value
of these registers for Port C is 0x0000.000F.
The default register type for the GPIOCR register is RO for all GPIO pins with the exception
of the NMI pin and the four JTAG/SWD pins (PB7 and PC[3:0]). These five pins are
currently the only GPIOs that are protected by the GPIOCR register. Because of this, the
register type for GPIO Port B7 and GPIO Port C[3:0] is R/W.
The default reset value for the GPIOCR register is 0x0000.00FF for all GPIO pins, with the
exception of the NMI pin and the four JTAG/SWD pins (PB7 and PC[3:0]). To ensure that
the JTAG port is not accidentally programmed as a GPIO, these four pins default to
non-committable. To ensure that the NMI pin is not accidentally programmed as the
non-maskable interrupt pin, it defaults to non-committable. Because of this, the default reset
value of GPIOCR for GPIO Port B is 0x0000.007F while the default reset value of GPIOCR
for Port C is 0x0000.00F0.
Table 9-6. GPIO Register Map
Offset Name
Type
0x000 GPIODATA
0x400 GPIODIR
0x404 GPIOIS
0x408 GPIOIBE
0x40C GPIOIEV
0x410 GPIOIM
0x414 GPIORIS
0x418 GPIOMIS
0x41C GPIOICR
0x420 GPIOAFSEL
0x500 GPIODR2R
0x504 GPIODR4R
0x508 GPIODR8R
0x50C GPIOODR
0x510 GPIOPUR
0x514 GPIOPDR
0x518 GPIOSLR
0x51C GPIODEN
0x520 GPIOLOCK
0x524 GPIOCR
0x528 GPIOAMSEL
0xFD0 GPIOPeriphID4
R/W
R/W
R/W
R/W
R/W
R/W
RO
RO
W1C
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
-
R/W
RO
Reset
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
-
0x0000.00FF
0x0000.0000
0x0000.0000
0x0000.0000
-
0x0000.0000
0x0000.0000
-
0x0000.0001
-
0x0000.0000
0x0000.0000
Description
GPIO Data
GPIO Direction
GPIO Interrupt Sense
GPIO Interrupt Both Edges
GPIO Interrupt Event
GPIO Interrupt Mask
GPIO Raw Interrupt Status
GPIO Masked Interrupt Status
GPIO Interrupt Clear
GPIO Alternate Function Select
GPIO 2-mA Drive Select
GPIO 4-mA Drive Select
GPIO 8-mA Drive Select
GPIO Open Drain Select
GPIO Pull-Up Select
GPIO Pull-Down Select
GPIO Slew Rate Control Select
GPIO Digital Enable
GPIO Lock
GPIO Commit
GPIO Analog Mode Select
GPIO Peripheral Identification 4
See
page
359
360
361
362
363
364
365
366
367
368
370
371
372
373
374
375
376
377
379
380
382
383
November 17, 2011
357
Texas Instruments-Production Data