DS90UB924-Q1 Datasheet, PDF (18/62 Pages) Texas Instruments – 5-MHz to 96-MHz 24-bit Color FPD-Link III to OpenLDI Deserializer With Bidirectional Control Channel

DS90UB924-Q1
SNLS512 – APRIL 2016
www.ti.com
Feature Description (continued)
7.3.7 Video Control Signals
The video control signal bits embedded in the high-speed FPD-Link (OpenLDI) LVDS are subject to certain
limitations relative to the video pixel clock period (PCLK). By default, the device applies a minimum pulse width
filter on these signals to help eliminate spurious transitions.
Normal Mode Control Signals (VS, HS, DE) have the following restrictions:
• Horizontal Sync (HS): The video control signal pulse width must be 3 PCLKs or longer when the Control
Signal Filter (register bit 0x03[4]) is enabled (default). Disabling the Control Signal Filter removes this
restriction (minimum is 1 PCLK). See Table 8. HS can have at most two transitions per 130 PCLKs.
• Vertical Sync (VS): The video control signal pulse is limited to 1 transition per 130 PCLKs. Thus, the minimum
pulse width is 130 PCLKs.
• Data Enable Input (DE): The video control signal pulse width must be 3 PCLKs or longer when the Control
Signal Filter (register bit 0x03[4]) is enabled (default). Disabling the Control Signal Filter removes this
restriction (minimum is 1 PCLK). See Table 8. DE can have at most two transitions per 130 PCLKs.
7.3.8 EMI Reduction Features
7.3.8.1 LVCMOS VDDIO Option
The 1.8 V/3.3 V LVCMOS inputs and outputs are powered from a separate VDDIO supply pin to offer
compatibility with external system interface signals. Note: When configuring the V_DDIO power supplies, all the
single-ended control input pins (except PDB) for device need to scale together with the same operating V_DDIO
levels. If V_DDIO is selected to operate in the 3.0 V to 3.6 V range, V_DDIO must be operated within 300 mV of V_DD33
(See Recommended Operating Conditions).
7.3.9 Built In Self Test (BIST)
An optional At-speed Built-In Self Test (BIST) feature supports testing of the high-speed serial link and the low-
speed back channel without external data connections. This is useful in the prototype stage, equipment
production, in-system test, and system diagnostics.
7.3.9.1 BIST Configuration and Status
The BIST mode is enabled at the deserializer by pin (BISTEN) or BIST configuration register. The test may
select either an external PCLK or the 33 MHz internal oscillator clock (OSC) frequency. In the absence of PCLK,
the user can select the internal OSC frequency at the deserializer through the BISTC pin or BIST configuration
register.
When BIST is activated at the deserializer, a BIST enable signal is sent to the serializer through the back
channel. The serializer outputs a test pattern and drives the link at speed. The deserializer detects the test
pattern and monitors it for errors. The deserializer PASS output pin toggles to flag each frame received
containing one or more errors. The serializer also tracks errors indicated by the CRC fields in each back channel
frame.
The BIST status can be monitored real time on the deserializer PASS pin, with each detected error resulting in a
half pixel clock period toggled LOW. After BIST is deactivated, the result of the last test is held on the PASS
output until reset (new BIST test or Power Down). A high on PASS indicates NO ERRORS were detected. A Low
on PASS indicates one or more errors were detected. The duration of the test is controlled by the pulse width
applied to the deserializer BISTEN pin. LOCK status is valid throughout the entire duration of BIST.
See Figure 20 for the BIST mode flow diagram.
18
Submit Documentation Feedback
Product Folder Links: DS90UB924-Q1
Copyright © 2016, Texas Instruments Incorporated