PIC16LF1454 Datasheet, PDF (371/418 Pages) Microchip Technology – 14/20-Pin Flash, 8-Bit USB Microcontrollers with XLP Technology

PIC16(L)F1454/5/9
TABLE 29-5: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C TA +125°C
Param
No.
Sym.
Characteristic
Min.
Typ† Max. Units Conditions
40* TT0H
T0CKI High Pulse Width
No Prescaler 0.5 TCY + 20 —
—
ns
With Prescaler
10
—
—
ns
41* TT0L
T0CKI Low Pulse Width
No Prescaler 0.5 TCY + 20 —
—
ns
With Prescaler
10
—
—
ns
42* TT0P
T0CKI Period
Greater of: —
—
ns N = prescale value
20 or TCY + 40
(2, 4, ..., 256)
N
45* TT1H
T1CKI High Synchronous, No Prescaler
0.5 TCY + 20 —
—
ns
Time
Synchronous,
15
—
—
ns
with Prescaler
Asynchronous
30
—
—
ns
46* TT1L
T1CKI Low Synchronous, No Prescaler
0.5 TCY + 20 —
—
ns
Time
Synchronous, with Prescaler
15
—
—
ns
Asynchronous
30
—
—
ns
47* TT1P
T1CKI Input Synchronous
Period
Greater of: —
—
ns N = prescale value
30 or TCY + 40
(1, 2, 4, 8)
N
Asynchronous
60
—
—
ns
49* TCKEZTMR1 Delay from External Clock Edge to Timer
Increment
2 TOSC
— 7 TOSC — Timers in Sync
mode
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: For proper operation, the minimum value of the ADC positive voltage reference must be 1.8V or greater.
TABLE 29-6: PIC16(L)F1454/5/9 A/D CONVERTER (ADC) CHARACTERISTICS:
Standard Operating Conditions (unless otherwise stated)
Operating temperature Tested at 25°C
Param
No.
Sym.
Characteristic
Min. Typ† Max. Units
Conditions
AD01 NR Resolution
—
—
10 bit
AD02 EIL Integral Error
—
—
±1.7 LSb VREF = 3.0V
AD03 EDL Differential Error
—
—
±1 LSb No missing codes
VREF = 3.0V
AD04 EOFF Offset Error
—
— ±2.5 LSb VREF = 3.0V
AD05 EGN Gain Error
AD06 VREF Reference Voltage⁽³⁾
—
—
±2.0 LSb VREF = 3.0V
1.8
—
VDD V VREF = (VREF+ minus VREF-)
AD07 VAIN Full-Scale Range
VSS
—
VREF V
AD08 ZAIN Recommended Impedance of
Analog Voltage Source
—
—
10 k Can go higher if external 0.01F capacitor is
present on input pin.
*
†
Note 1:
2:
3:
4:
These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Total Absolute Error includes integral, differential, offset and gain errors.
The A/D conversion result never decreases with an increase in the input voltage and has no missing codes.
ADC VREF is from external VREF+ pin, VDD pin, whichever is selected as reference input.
When ADC is off, it will not consume any current other than leakage current. The power-down current specification
includes any such leakage from the ADC module.
 2012 Microchip Technology Inc.
Preliminary
DS41639A-page 371