PIC32MX1XX_12 Datasheet, PDF (186/328 Pages) Microchip Technology – 32-bit Microcontrollers (up to 128 KB Flash and 32 KB SRAM) with Audio and Graphics Interfaces, USB, and Advanced Analog

PIC32MX1XX/2XX
REGISTER 19-2: PMMODE: PARALLEL PORT MODE REGISTER
Bit
Bit
Bit
Bit
Bit
Bit
Bit
Range 31/23/15/7 30/22/14/6 29/21/13/5 28/20/12/4 27/19/11/3 26/18/10/2
31:24
23:16
15:8
7:0
U-0
U-0
U-0
—
—
—
U-0
U-0
U-0
—
—
—
R-0
BUSY
R/W-0
R/W-0
IRQM<1:0>
R/W-0
R/W-0
WAITB<1:0>⁽¹⁾
R/W-0
U-0
U-0
—
—
U-0
U-0
—
—
R/W-0
R/W-0
INCM<1:0>
R/W-0
R/W-0
WAITM<3:0>⁽¹⁾
U-0
—
U-0
—
U-0
—
R/W-0
Bit
Bit
25/17/9/1 24/16/8/0
U-0
U-0
—
—
U-0
U-0
—
—
R/W-0
R/W-0
MODE<1:0>
R/W-0
R/W-0
WAITE<1:0>⁽¹⁾
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
bit 31-16 Unimplemented: Read as ‘0’
bit 15 BUSY: Busy bit (Master mode only)
1 = Port is busy
0 = Port is not busy
bit 14-13 IRQM<1:0>: Interrupt Request Mode bits
11 = Reserved, do not use
10 = Interrupt generated when Read Buffer 3 is read or Write Buffer 3 is written (Buffered PSP mode)
or on a read or write operation when PMA<1:0> =11 (Addressable Slave mode only)
01 = Interrupt generated at the end of the read/write cycle
00 = No Interrupt generated
bit 12-11 INCM<1:0>: Increment Mode bits
11 = Slave mode read and write buffers auto-increment (PMMODE<1:0> = 00 only)
10 = Decrement ADDR<10:2> and ADDR<14> by 1 every read/write cycle⁽²⁾
01 = Increment ADDR<10:2> and ADDR<14> by 1 every read/write cycle⁽²⁾
00 = No increment or decrement of address
bit 10 Unimplemented: Read as ‘0’
bit 9-8 MODE<1:0>: Parallel Port Mode Select bits
11 = Master mode 1 (PMCS1, PMRD/PMWR, PMENB, PMA<x:0>, and PMD<7:0>)
10 = Master mode 2 (PMCS1, PMRD, PMWR, PMA<x:0>, and PMD<7:0>)
01 = Enhanced Slave mode, control signals (PMRD, PMWR, PMCS1, PMD<7:0>, and PMA<1:0>)
00 = Legacy Parallel Slave Port, control signals (PMRD, PMWR, PMCS1, and PMD<7:0>)
bit 7-6 WAITB<1:0>: Data Setup to Read/Write Strobe Wait States bits⁽¹⁾
11 = Data wait of 4 TPB; multiplexed address phase of 4 TPB
10 = Data wait of 3 TPB; multiplexed address phase of 3 TPB
01 = Data wait of 2 TPB; multiplexed address phase of 2 TPB
00 = Data wait of 1 TPB; multiplexed address phase of 1 TPB (default)
Note 1: Whenever WAITM<3:0> = 0000, WAITB and WAITE bits are ignored and forced to 1 TPBCLK cycle for a
write operation; WAITB = 1 TPBCLK cycle, WAITE = 0 TPBCLK cycles for a read operation.
2: Address bit A14 is not subject to auto-increment/decrement if configured as Chip Select CS1.
DS61168E-page 186
Preliminary
 2011-2012 Microchip Technology Inc.