PIC32MX1XX_12 Datasheet, PDF (164/328 Pages) Microchip Technology – 32-bit Microcontrollers (up to 128 KB Flash and 32 KB SRAM) with Audio and Graphics Interfaces, USB, and Advanced Analog

PIC32MX1XX/2XX
REGISTER 16-1: SPIxCON: SPI CONTROL REGISTER
Bit
Bit
Bit
Bit
Bit
Bit
Bit
Bit
Bit
Range 31/23/15/7 30/22/14/6 29/21/13/5 28/20/12/4 27/19/11/3 26/18/10/2 25/17/9/1 24/16/8/0
31:24
23:16
15:8
7:0
R/W-0
FRMEN
R/W-0
MCLKSEL⁽²⁾
R/W-0
ON⁽¹⁾
R/W-0
SSEN
R/W-0
FRMSYNC
U-0
—
U-0
—
R/W-0
CKP⁽⁴⁾
R/W-0
FRMPOL
U-0
—
R/W-0
SIDL
R/W-0
MSTEN
R/W-0
MSSEN
U-0
—
R/W-0
DISSDO
R/W-0
DISSDI
R/W-0
FRMSYPW
R/W-0
R/W-0
R/W-0
FRMCNT<2:0>
U-0
U-0
R/W-0
R/W-0
—
—
SPIFE ENHBUF⁽²⁾
R/W-0
MODE32
R/W-0
MODE16
R/W-0
SMP
R/W-0
CKE⁽³⁾
R/W-0
R/W-0
R/W-0
R/W-0
STXISEL<1:0>
SRXISEL<1:0>
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
bit 31
FRMEN: Framed SPI Support bit
1 = Framed SPI support is enabled (SSx pin used as FSYNC input/output)
0 = Framed SPI support is disabled
bit 30
FRMSYNC: Frame Sync Pulse Direction Control on SSx pin bit (Framed SPI mode only)
1 = Frame sync pulse input (Slave mode)
0 = Frame sync pulse output (Master mode)
bit 29
FRMPOL: Frame Sync Polarity bit (Framed SPI mode only)
1 = Frame pulse is active-high
0 = Frame pulse is active-low
bit 28
MSSEN: Master Mode Slave Select Enable bit
1 = Slave select SPI support enabled. The SS pin is automatically driven during transmission in
Master mode. Polarity is determined by the FRMPOL bit.
0 = Slave select SPI support is disabled.
bit 27
FRMSYPW: Frame Sync Pulse Width bit
1 = Frame sync pulse is one character wide
0 = Frame sync pulse is one clock wide
bit 26-24 FRMCNT<2:0>: Frame Sync Pulse Counter bits. Controls the number of data characters transmitted per
pulse. This bit is only valid in FRAMED_SYNC mode.
111 = Reserved; do not use
110 = Reserved; do not use
101 = Generate a frame sync pulse on every 32 data characters
100 = Generate a frame sync pulse on every 16 data characters
011 = Generate a frame sync pulse on every 8 data characters
010 = Generate a frame sync pulse on every 4 data characters
001 = Generate a frame sync pulse on every 2 data characters
000 = Generate a frame sync pulse on every data character
bit 23
MCLKSEL: Master Clock Enable bit⁽²⁾
1 = REFCLK is used by the Baud Rate Generator
0 = PBCLK is used by the Baud Rate Generator
bit 22-18 Unimplemented: Read as ‘0’
Note 1:
2:
3:
4:
When using the 1:1 PBCLK divisor, the user’s software should not read or write the peripheral’s SFRs in
the SYSCLK cycle immediately following the instruction that clears the module’s ON bit.
This bit can only be written when the ON bit = 0.
This bit is not used in the Framed SPI mode. The user should program this bit to ‘0’ for the Framed SPI
mode (FRMEN = 1).
When AUDEN = 1, the SPI module functions as if the CKP bit is equal to ‘1’, regardless of the actual value
of CKP.
DS61168E-page 164
Preliminary
 2011-2012 Microchip Technology Inc.