IS75V16F128GS32 Datasheet, PDF (5/52 Pages) Integrated Silicon Solution, Inc – 3.0 Volt Multi-Chip Package (MCP) 128 Mbit Simultaneous Operation Flash Memory and 32 Mbit Pseudo Static RAM

IS75V16F128GS32
ISSI ^®
ABSOLUTE MAXIMUM RATINGS^(1,5)
Symbol
Tstg
TA
VIN,VOUT
Parameter
Storage Temperature
Ambient Temperature with Power Applied
Voltage with Respect to Ground All Pins⁽²⁾
Rating
Min.
Max.
–55
+125
–30
+85
–0.3
VCC + 0.3⁽⁶⁾
Unit
°C
°C
V
VCCf1,VCCf2
VCCr
VCCf Supply⁽²⁾
VCCr Supply⁽²⁾
–0.3
3.5
V
–0.3
3.5
V
VIN
RESET1, RESET2⁽³⁾
-0.5
+13.0
V
VACC
WP/ACC⁽⁴⁾
–0.5
+10.5
V
Notes:
1. Voltage is defined on the basis of GND = 0 V.
2. Minimum DC voltage on input or I/O pins is -0.3 V. During voltage transitions, input or I/O pins may undershoot
GND to -1.0 V for periods of up to 20 ns. Maximum DC voltage on input or I/O pins is VCCf1+ 0.3V , VCCf2+ 0.3V
or VCCr + 0.3 V. During voltage transitions, input or I/O pins may overshoot to VCCf1+ 2.0V , VCCf2+ 2.0 V or VCCr + 1.0 V
for periods of up to 20 ns.
3. Minimum DC input voltage on RESET1 or RESET2 pin is -0.5 V. During voltage transitions, RESET1 or RESET2 pin may
undershoot GND to -2.0 V for periods of up to 20 ns.
The voltage difference between input and supply voltage (VIN-VCCf1 or VCCf2) does not exceed 9.0 V.
The maximum DC input voltage on the RESET pin is +13.0 V that may overshoot to +14.0 V for periods of up to 20 ns.
4. Minimum DC input voltage on WP/ACC pin is -0.5 V. During voltage transitions, WP/ACC pin may undershoot
GND to -2.0 V for periods of up to 20 ns. Maximum DC input voltage on WP/ACC pin is +10.5 V which may
overshoot to +12.0 V for periods of up to 20 ns, when VCCf1 or VCCf2 is applied.
5. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
reliability.
6. This Vcc refers to the minimum of VCCf1, VCCf2, _or Vccr .
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
TA
Ambient Temperature
VCCf1,VCCf2 VCCf Supply Voltages
VCCr
VCCr Supply Voltages
Note:
Voltage is defined on the basis of GND = 0 V.
Rating
Min.
Max.
Unit
–30
+85
°C
2.7
3.3
V
2.7
3.3
V
Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774
5
PRELIMINARY INFORMATION Rev. 00D
03/24/03