MC9S08SH32CWL Datasheet, PDF (293/328 Pages) Freescale Semiconductor, Inc – MC9S08SH32 Series Features

Appendix A Electrical Characteristics
Table A-6. DC Characteristics (continued)
Num C
Characteristic
Symbol
Condition
Min
Typ¹
Max Unit
14 D RAM retention voltage
15 D POR re-arm voltage⁸
16 D POR re-arm time⁹
V_RAM
V_POR
t_POR
—
0.6
1.0
V
0.9
1.4
2.0
V
10
—
—
μs
Low-voltage detection threshold —
17 ^{P high range}
V_DD falling
V_DD rising
V_LVD1
3.9
4.0
4.1
V
4.0
4.1
4.2
Low-voltage detection threshold —
18 ^{P low range}
V_DD falling
V_DD rising
V_LVD0
2.48
2.56
2.64
V
2.54
2.62
2.70
Low-voltage warning threshold —
19 ^{P high range 1}
V_LVW3
V_DD falling
V_DD rising
4.5
4.6
4.7
V
4.6
4.7
4.8
Low-voltage warning threshold —
20 ^{P high range 0}
V_LVW2
V_DD falling
V_DD rising
4.2
4.3
4.4
V
4.3
4.4
4.5
Low-voltage warning threshold
21 ^{P low range 1}
V_LVW1
V_DD falling
V_DD rising
2.84
2.92
3.00
V
2.90
2.98
3.06
Low-voltage warning threshold —
22 ^{P low range 0}
V_LVW0
V_DD falling
V_DD rising
2.66
2.74
2.82
V
2.72
2.80
2.88
T Low-voltage inhibit reset/recover
23
hysteresis
V_hys
5V
3V
—
100
—
mV
—
60
—
24 P Bandgap Voltage Reference¹⁰
V_BG
1.18
1.202
1.21
V
1 _{Typical values are measured at 25°C. Characterized, not tested}
2 _{When IRQ or a pin interrupt is configured to detect rising edges, pulldown resistors are used in place of pullup resistors.}
3 _{The specified resistor value is the actual value internal to the device. The pullup value may measure higher when measured}
externally on the pin.
4 _{Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current}
conditions. If positive injection current (V_In > V_DD) is greater than I_DD, the injection current may flow out of V_DD and could result
in external power supply going out of regulation. Ensure external V_DD load will shunt current greater than maximum injection
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or
if clock rate is very low (which would reduce overall power consumption).
5 _{All functional non-supply pins except RESET are internally clamped to VSS and VDD. In MC9S08SH32, the RESET pin is}
named “PTA5/IRQ/TCLK/RESET.”
6 _{Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate}
resistance values for positive and negative clamp voltages, then use the larger of the two values.
7 _{The RESET pin does not have a clamp diode to VDD. Do not drive this pin above VDD.}
8 _{Maximum is highest voltage that POR is guaranteed.}
9 _{Simulated, not tested.}
10 _{Factory trimmed at VDD = 5.0 V, Temp = 25°C.}
MC9S08SH32 Series Data Sheet, Rev. 2
Freescale Semiconductor
293
PRELIMINARY