AM186 Datasheet, PDF (37/112 Pages) Advanced Micro Devices – High-Performance, 80C186- and 80C188-Compatible, 16-Bit Embedded Microcontrollers with RAM

S1/IMDIS
Bus Cycle Status (output, three-state,
synchronous)
Internal Memory Disable (input, internal pullup)
S1—This pin indicates to the system the type of bus
cycle in progress. S1 can be used as a data transmit or
receive indicator. S2–S0 are three-stated during bus
holds, hold acknowledges, and ONCE mode. During
reset, these pins are pullups. The S2–S0 pins are en-
coded as shown in Table 5.
IMDIS—If asserted during reset, this pin disables inter-
nal memory. Internal memory disable mode is provided
for emulation and debugging purposes.
S0/SREN
CLKSEL1—The clocking mode of the Am186ER and
Am188ER microcontrollers is controlled by UZI/
CLKSEL2/PIO26 and S6/CLKSEL1/PIO29. Both
CLKSEL2 and CLKSEL1 are held High during power-
on reset because of an internal pullup resistor. This is
the default clocking mode—Times Four. If CLKSEL1 is
held Low during power-on reset, the chip enters the Di-
vide by Two clocking mode where the fundamental
clock is derived by dividing the external clock input by
2. If Divide by Two mode is selected, the PLL is dis-
abled. This pin is latched within three crystal clock cy-
cles after the rising edge of RES. Refer to Reset
Waveforms on page 100 and Signals Related to Reset
Waveforms on page 100 to determine signal hold
times. See Table 6 on page 39 for more information on
the clocking modes.
Bus Cycle Status (output, three-state,
If S6 is used as PIO29 in input mode, the device driving
synchronous)
Show Read Enable (input, internal pullup)
S0—This pin indicates to the system the type of bus
cycle in progress. S2–S0 are three-stated during bus
holds, hold acknowledges, and ONCE mode. During
reset, these pins are pullups. The S2–S0 pins are en-
T ^{coded as shown in Table 5.}
SREN—If asserted during reset, this pin enables data
read from internal memory to be shown/driven on the
AD15–AD0 bus. Note that if a byte read is being shown,
F _{the unused byte will also be driven on the AD15–AD0}
bus.This mode is provided for emulation and debug-
ging purposes.
A _{Table 5. Bus Cycle Encoding}
S2
S1
S0 Bus Cycle
0
0
0 Interrupt acknowledge
0
0
1 Read data from I/O
R ₀
1
0 Write data to I/O
0
1
1 Halt
1
0
0 Instruction fetch
D¹
0
1 Read data from memory
PIO29 must not drive the pin Low during power-on reset.
S6/CLKSEL1/PIO29 defaults to a PIO input with pullup,
so the pin does not need to be driven High externally.
SCLK/PIO20
Serial Clock (output, synchronous)
This pin supplies the synchronous serial interface (SSI)
clock to a slave device, allowing transmit and receive
operations to be synchronized between the microcon-
troller and the slave. SCLK is derived from the micro-
controller internal clock and then divided by 2, 4, 8, or
16 depending on register settings.
An access to any of the SSR or SSD registers acti-
vates SCLK for eight SCLK cycles (see Figure 14 and
Figure 15 on page 58). When SCLK is inactive, it is
held High by the microcontroller. SCLK is three-stated
during ONCE mode.
SDATA/PIO21
Serial Data (input/output, synchronous)
This pin transmits and receives synchronous serial in-
terface (SSI) data to and from a slave device. When
SDATA is inactive, a weak keeper holds the last value
of SDATA on the pin.
SDEN1/PIO23, SDEN0/PIO22
1
1
0 Write data to memory
1
1
1 None (passive)
Serial Data Enables (output, synchronous)
These pins enable data transfers on port 1 and port 0
S6/CLKSEL1/PIO29
Bus Cycle Status Bit 6 (output, synchronous)
Clock Select 1 (input, internal pullup)
of the synchronous serial interface (SSI). The micro-
controller asserts either SDEN1 or SDEN0 at the be-
ginning of a transfer and deasserts it after the transfer
is complete. When SDEN1–SDEN0 are inactive, they
S6—During the second and remaining periods of a are held Low by the microcontroller. SDEN1–SDEN0
cycle (t₂, t₃, and t₄), this pin is asserted High to indicate
a DMA-initiated bus cycle. During a bus hold or reset
are three-stated during ONCE mode.
condition, S6 is three-stated.
Am186^TMER and Am188^TMER Microcontrollers Data Sheet
37