|
DS90UB921-Q1 Datasheet, PDF (7/57 Pages) Texas Instruments – 5 - 96 MHz 24-bit Color FPD-Link III Serializer with Bidirectional Control Channel | |||
|
◁ |
www.ti.com
DS90UB921-Q1
SNLS488 â MARCH 2016
6.5 Thermal Information
THERMAL METRIC(1)
DS90UB921-Q1
RHS (WQFN)
UNIT
48 PINS
RθJA
RθJC(top)
RθJB
ÏJT
ÏJB
RθJC(bot)
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
29
11.7
5.0
°C/W
0.1
6.0
1.7
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
6.6 DC Electrical Characteristics
over operating free-air temperature range (unless otherwise noted)(1)(2)(3)
PARAMETER
TEST CONDITIONS
PIN/FREQ.
MIN TYP
MAX UNIT
LVCMOS I/O DC SPECIFICATIONS
VIH
High-level input voltage VDDIO = 3 V to 3.6 V
2
VIL
Low-level input voltage VDDIO = 3 V to 3.6 V
IIN
Input current
VIN = 0 V or
VIN = VDDIO (3 V to 3.6 V)
PDB
GND
â10
VDDIO = 3 V to 3.6 V
2
VIH
High-level input voltage
VDDIO = 1.71 V to 1.89 V
0.65 Ã
VDDIO
VDDIO = 3 V to 3.6 V
VIL
Low-level input voltage
VDDIO = 1.71 V to 1.89 V
DIN[23:0], HS,
VS, DE, PCLK,
I2S_CLK,
I2S_WC,
GND
GND
IIN
Input current
VIN = 0 V or
VDDIO = 3 V to
3.6 V
I2S_DA
â10
VIN = VDDIO
VDDIO = 1.71 V
to 1.89 V
â10
VDDIO
V
0.8
V
±1
10
µA
VDDIO
V
VDDIO
V
0.8
V
0.35 Ã
VDDIO
V
±1
10
µA
±1
10
µA
VOH
High-level output
voltage
IOH = â4 mA
VDDIO = 3 V to
3.6 V
VDDIO = 1.71 V
to 1.89 V
2.4
VDDIO â
0.45
VDDIO
V
VDDIO
V
VOL
Low-level output
voltage
IOH = 4 mA
VDDIO = 3 V to
3.6 V
VDDIO = 1.71 V
to 1.89 V
GPIO[3:0],
GPO_REG[7:4],
REM_INTB
GND
GND
0.4
V
0.35
V
IOS
Output short-circuit
current
VOUT = 0 V
â50
mA
IOZ
TRI-STATE output
current
VOUT = 0 V or
VOUT = VDDIO
PDB = L
â10
10
µA
(1) The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as
otherwise modified or specified by the Electrical Characteristics conditions and/or Notes. Typical specifications are estimations only and
are not ensured.
(2) Typical values represent most likely parametric norms at nominal conditions at the time of product characterization and are not ensured.
(3) Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground
except VOD and ÎVOD, which are differential voltages.
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: DS90UB921-Q1
Submit Documentation Feedback
7
|
▷ |