TI380C25 Datasheet, PDF (40/71 Pages) Texas Instruments – TOKEN-RING COMMPROCESSOR

TI380C25
TOKEN-RING COMMPROCESSOR
SPWS012 – JANUARY 1995
80x8x DIO read-cycle timing
25-MHz OPERATION
33-MHz OPERATION
NO.
UNIT
MIN
MAX
MIN
MAX
255 Delay time, SRDY low to either SCS or SRD high
15
15
ns
256 Pulse duration, SRAS high
30
30
ns
259†
Hold time, SAD in the high-impedance state after SRD low
(see Note 19)
0
0
ns
260
Setup time, SADH0 – SADH7, SADL0 – SADL7, SPH, and
SPL valid before SRDY low
0
0
ns
261†
Delay time, SRD or SCS high to SAD in the high-impedance
state (see Note 19)
35
35
ns
261a
Hold time, output data valid after SRD or SCS high
(see Note 19)
0
0
ns
Setup time, SRSX, SRS0 – SRS2, SCS, and SBHE valid to
264
SRAS no longer high (see Note 20)
30
30
ns
265
Hold time, SRSX, SRS0 – SRS2, SCS, and SBHE valid after
SRAS low
10
10
ns
266a Setup time, SRAS high to SRD no longer high (see Note 20) 15
15
ns
267‡
Setup time, SRSX, SRS0 – SRS2 valid before SRD no longer
high (see Note 19)
15
15
ns
268
Hold time, SRSX, SRS0 – SRS2 valid after SRD no longer low
(see Note 20)
0
0
ns
272a
Setup time, SRD, SWR, and SIACK high from previous cycle
to SRD no longer high
tc(SCK)
tc(SCK)
ns
273a
275
Hold time, SRD, SWR, and SIACK high after SRD high
Delay time, SRD and SWR, or SCS high to SRDY high
(see Note 19)
tc(SCK)
0
tc(SCK)
25
0
ns
25
ns
279†
Delay time, SRD and SWR, high to SRDY in the
high-impedance state
0
tc(SCK)
0
tc(SCK) ns
282a
282R
Delay time, SDBEN low to SRDY low in a read cycle
Delay time, SRD low to SDBEN low (see TMS380 Second
Generation Token-Ring User’s Guide, SPWU005, subsection
3.4.1.1.1), provided previous cycle completed
0
tc(SCK) / 2 + 4
0
tc(SCK) + 3
0
tc(SCK) / 2 + 4 ns
0
tc(SCK) + 3 ns
283R Delay time, SRD high to SDBEN high (see Note 19)
0
tc(SCK) / 2 + 4
0
tc(SCK) / 2 + 4 ns
286
Pulse duration, SRD high between DIO accesses
(see Note 19)
tc(SCK)
tc(SCK)
ns
† _{This specification is provided as an aid to board design. It is not assured during manufacturing testing.}
‡ _{It is the later of SRD and SWR or SCS low that indicates the start of the cycle.}
NOTES: 19. The inactive chip select is SIACK in DIO read and DIO write cycles, and SCS is the inactive chip select in interrupt-acknowledge
cycles.
20. In 80x8x mode, SRAS can be used to strobe the values of SBHE, SRSX, SRS0 – SRS2, and SCS. When used to do so, SRAS must
meet parameter 266a, and SBHE, SRS0 – SRS2, and SCS must meet parameter 264. If SRAS is strapped high, parameters 266a
and 264 are irrelevant and parameter 268 must be met.
40
• POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443