DS90UR916Q_13 Datasheet, PDF (36/45 Pages) Texas Instruments – 5 - 65 MHz 24-bit Color FPD-Link II Deserializer with Image Enhancement

DS90UR916Q
SNOSB46E – MARCH 2011 – REVISED APRIL 2013
www.ti.com
POWER UP REQUIREMENTS AND PDB PIN
At power-on, the PDB pin must be LOW. The transition to the HIGH state (normal operating mode) may only
occur after all power supplies are stable and above the minimum recommended operating voltage. All other
LVCMOS inputs must also remain LOW prior to power supplies stabilized at the recommended operating
voltages. Active driving of inputs and the transition of PDB to the HIGH state should be delayed 1usec after
power supplies are stabilized.
TRANSMISSION MEDIA
The Ser/Des chipset is intended to be used in a point-to-point configuration, through a PCB trace, or through
twisted pair cable. The Ser and Des provide internal terminations providing a clean signaling environment. The
interconnect for LVDS should present a differential impedance of 100 Ohms. Use cables and connectors that
have matched differential impedance to minimize impedance discontinuities. Shielded or un-shielded cables may
be used depending upon the noise environment and application requirements.
LIVE LINK INSERTION
The Ser and Des devices support live pluggable applications. The automatic receiver lock to random data “plug &
go” hot insertion capability allows the DS90UR916Q to attain lock to the active data stream during a live insertion
event.
PCB LAYOUT AND POWER SYSTEM CONSIDERATIONS
Circuit board layout and stack-up for the LVDS Ser/Des devices should be designed to provide low-noise power
feed to the device. Good layout practice will also separate high frequency or high-level inputs and outputs to
minimize unwanted stray noise pickup, feedback and interference. Power system performance may be greatly
improved by using thin dielectrics (2 to 4 mils) for power / ground sandwiches. This arrangement provides plane
capacitance for the PCB power system with low-inductance parasitics, which has proven especially effective at
high frequencies, and makes the value and placement of external bypass capacitors less critical. External bypass
capacitors should include both RF ceramic and tantalum electrolytic types. RF capacitors may use values in the
range of 0.01 uF to 0.1 uF. Tantalum capacitors may be in the 2.2 uF to 10 uF range. Voltage rating of the
tantalum capacitors should be at least 5X the power supply voltage being used.
Surface mount capacitors are recommended due to their smaller parasitics. When using multiple capacitors per
supply pin, locate the smaller value closer to the pin. A large bulk capacitor is recommend at the point of power
entry. This is typically in the 50uF to 100uF range and will smooth low frequency switching noise. It is
recommended to connect power and ground pins directly to the power and ground planes with bypass capacitors
connected to the plane with via on both ends of the capacitor. Connecting power or ground pins to an external
bypass capacitor will increase the inductance of the path.
A small body size X7R chip capacitor, such as 0603, is recommended for external bypass. Its small body size
reduces the parasitic inductance of the capacitor. The user must pay attention to the resonance frequency of
these external bypass capacitors, usually in the range of 20-30 MHz. To provide effective bypassing, multiple
capacitors are often used to achieve low impedance between the supply rails over the frequency of interest. At
high frequency, it is also a common practice to use two vias from power and ground pins to the planes, reducing
the impedance at high frequency.
Some devices provide separate power and ground pins for different portions of the circuit. This is done to isolate
switching noise effects between different sections of the circuit. Separate planes on the PCB are typically not
required. Pin Description tables typically provide guidance on which circuit blocks are connected to which power
pin pairs. In some cases, an external filter many be used to provide clean power to sensitive circuits such as
PLLs.
Use at least a four layer board with a power and ground plane. Locate LVCMOS signals away from the LVDS
lines to prevent coupling from the LVCMOS lines to the LVDS lines. Closely-coupled differential lines of 100
Ohms are typically recommended for LVDS interconnect. The closely coupled lines help to ensure that coupled
noise will appear as common-mode and thus is rejected by the receivers. The tightly coupled lines will also
radiate less.
Information on the WQFN style package is provided in TI Application Note: AN-1187 (SNOA401).
36
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR916Q