TLE9263-3QX Datasheet, PDF (58/198 Pages) Infineon Technologies AG – Dedicated Data Sheets are available for the different product variants

6.3
Electrical Characteristics
TLE9263-3QX
Voltage Regulator 1
Table 16 Electrical Characteristics
V_S = 5.5 V to 28 V; T_j = -40 °C to +150 °C; all voltages with respect to ground, positive current flowing into pin
(unless otherwise specified)
Parameter
Symbol
Values
Unit Note / Test Condition Number
Output Voltage including line V_CC1,out1
and Load regulation
Min. Typ. Max.
4.9 5.0 5.1 V
Output Voltage including line
and Load regulation
Output Voltage including line
and Load regulation
V_CC1,out2
V_CC1,out3
4.9 5.0
4.97 –
5.1 V
5.07 V
1)_{SBC Normal Mode;}
10µA < I_VCC1 < 250mA
6V < V_S < 28V
1)_{SBC Normal Mode;}
10µA < I_VCC1 < 150mA
1)2)_{SBC Normal Mode;}
20mA < IVCC1 < 90mA
8V < VS < 18V
25°C < Tj < 125°C
P_6.3.1
P_6.3.7
P_6.3.12
Output Voltage including line V_CC1,out41 4.9 5.05 5.2 V
and Load regulation
SBC Stop Mode;
P_6.3.2
1mA < I_VCC1 < I_VCC1,Ipeak
Output Voltage including line V_CC1,out42 4.9
and Load regulation
5.05 5.25 V
SBC Stop Mode;
10µA < I_VCC1 < 1mA
P_6.3.20
Output Drop
V_CC1,d1
–
–
500 mV I_VCC1 = 50mA
V_S=3V
P_6.3.3
Output Drop
V_CC1,d2
–
VCC1 Active Peak Threshold 1 I_{VCC1,Ipeak1,r} –
(Transition threshold between
low-power and high-power
mode regulator)
–
500 mV I_VCC1 = 150mA
V_S=5V
1.9 3.5
mA ²⁾ I_CC1 rising;
V_S = 13.5V
-40°C < T_j < 150°C;
I_PEAK_TH = ‘0’
P_6.3.4
P_6.3.13
VCC1 Active Peak Threshold 1 I_{VCC1,Ipeak1,f} 0.5 1.3 –
(Transition threshold between
high-power and low-power
mode regulator)
mA ²⁾ I_CC1 falling;
V_S = 13.5V
-40°C < T_j < 150°C;
I_PEAK_TH = ‘0’
P_6.3.17
VCC1 Active Peak Threshold 2 I_{VCC1,Ipeak2,r} –
(Transition threshold between
low-power and high-power
mode regulator)
4.3 7.0
mA ²⁾ I_CC1 rising;
V_S = 13.5V
-40°C < T_j < 150°C;
I_PEAK_TH = ‘1’
P_6.3.18
VCC1 Active Peak Threshold 2 I_{VCC1,Ipeak2,f} 1.7 3.4 –
(Transition threshold between
high-power and low-power
mode regulator)
mA ²⁾ I_CC1 falling;
V_S = 13.5V
-40°C < T_j < 150°C;
I_PEAK_TH = ‘1’
P_6.3.19
Over Current Limitation
I_VCC1,lim
250 –
1200²⁾ mA current flowing out of P_6.3.6
pin, V_CC1 = 0V
1)In SBC Stop Mode, the specified output voltage tolerance applies when I_VCC1 has exceeded the selected active
peak threshold I( _{VCC1,Ipeak1,r} or I_{VCC1,Ipeak2,r}) but with increased current consumption.
2) Not subject to production test, specified by design.
Data Sheet
58
Rev. 1.1, 2014-09-26