3UG4622-1AW30 Datasheet, PDF (17/114 Pages) List of Unclassifed Manufacturers – Monitoring and Control Devices

SIMOCODE 3UF Motor Management and Control Devices
Temperature modules
Mounting
Displays
• Green LED "READY"
System interfaces
Sensor circuits
Typical sensor circuits
• PT100
• PT1000/KTY83/KTY84/NTC
Wire-break/short-circuit detection
• For sensor type
• Open-circuit
• Short-circuit
• Measuring range
Measuring accuracy at 20 °C ambient temperature (T20)
Deviation due to ambient temperature (in % of measuring range)
Conductor cross-sections
• Tightening torque
• Solid
• Finely stranded with end sleeve
• AWG cable (solid)
• AWG cable (finely stranded)
Analog modules
Mounting
Displays
• Green LED "READY"
System interfaces
Control circuits
Inputs
• Channels
• Parameterizable measuring ranges
• Shielding
• Max. input current (destruction limit)
• Accuracy
• Input resistance
• Conversion time
• Resolution
• Open-circuit detection
Outputs
• Channels
• Parameterizable output range
• Shielding
• Max. voltage at output
• Accuracy
• Max. output load
• Conversion time
• Resolution
• Short-circuit resistant
Connection type
Voltage isolation of inputs/outputs to the device electronics
Conductor cross-sections
• Tightening torque
• Solid
• Finely stranded with end sleeve
• AWG cable (solid)
• AWG cable (finely stranded)
SIMOCODE pro 3UF7
motor management and control devices
Snap-on mounting onto 35 mm standard mounting rail or
screw fixing with additional push-in lugs
Continuous light: "Ready"
Flashing:
"No connection to the PC"
for connecting to a basic unit, another expansion module, a current
measuring module or current/voltage measuring module or to the operator
panel
mA 1 (typical)
mA 0.2 (typical)
PT100/PT1000 KTY83-110
•
•
•
•
°C -50 ... +500
-50 ... +175
K
< –2
%
0.05 per K deviation from T20
KTY84
•
•
-40 ... +300
Nm
mm²
mm²
AWG
AWG
0.8 ... 1.2
1 × (0.5 ... 4.0); 2 × (0.5 ... 2.5)
1 × (0.5 ... 2.5); 2 × (0.5 ... 1.5)
1 x AWG 20 to 12/2 x AWG 20 to 14
1 x AWG 20 to 14/2 x AWG 20 to 16
NTC
--
•
+80 ... +160
Snap-on mounting onto 35 mm standard mounting rail or
screw fixing with additional push-in lugs
Continuous light: "Ready"
Flashing:
"No connection to the PC"
for connecting to a basic unit, another expansion module, a current
measuring module or current/voltage measuring module or to the operator
panel
2
mA 0/4 ... 20
up to 30 m shield recommended, from 30 m shield required
mA 40
%
1
W
50
ms 130
bit 12
with measuring range 4 ... 20 mA
1
mA 0/4 ... 20
up to 30 m shield recommended, from 30 m shield required
30 V DC
%
1
W
500
ms 10
bit 12
yes
2-wire connection
no
Nm
mm²
mm²
AWG
AWG
0.8 ... 1.2
1 x (0.5 ... 4.0); 2 x (0.5 ... 2.5)
1 x (0.5 ... 2.5); 2 x (0.5 ... 1.5)
1 x AWG 20 to 12/2 x AWG 20 to 14
1 x AWG 20 to 14/2 x AWG 20 to 16
Siemens LV 1 T · 2006
7/17