3UG4622-1AW30 Datasheet, PDF (13/114 Pages) List of Unclassifed Manufacturers – Monitoring and Control Devices

SIMOCODE 3UF Motor Management and Control Devices
Diagnostic data
• Numerous detailed early warning and fault messages (can
also be used for further processing in the device or I&C
system)
• Internal device fault logging with time stamp
• Value of the previous tripping current
• Checkback error (e.g. no current flow in the main circuit
following ON control command) etc.
SIMOCODE pro 3UF7
motor management and control devices
Autonomous operation
An essential feature of SIMOCODE pro is independent
execution of all protection and control functions even if
communication with the I&C system breaks down. If the bus or
automation system fails, the full functionality of the feeder is
ensured or a pre-defined response can be initiated, e.g. the
feeder can be shut down in a controlled manner or certain
configured control mechanisms can be performed (e.g. the
direction of rotation can be reversed).
■ Integration
General
In addition to device function and hardware design, a great deal
of emphasis is placed on the case of communication-capable
controlgear on the user-friendliness of the configuration software
and the ability of the system to be integrated easily into various
different system configurations and process automation sys-
tems. For this reason, the SIMOCODE pro system provides suit-
able software tools for consistent, time-saving parameterization,
configuration and diagnostics:
• SIMOCODE ES for totally integrated startup and service
• OM SIMOCODE pro object manager for total integration into
SIMATIC S7
• PCS 7 function block library SIMOCODE pro for total
integration into PCS 7
SIMOCODE ES
The parameterization software for SIMOCODE pro can be run on
a PC/PG under Windows 2000 or Windows XP. It is available in
two functionally graded versions:
• SIMOCODE ES Smart, for direct connection to
SIMOCODE pro via the system interface on the device
(point-to-point)
• SIMOCODE ES Professional, for connection to one or
several devices over PROFIBUS DP or point-to-point through
the system interface
With SIMOCODE ES, the SIMOCODE motor management sys-
tem provides a user-friendly and clear-cut user interface with
which to configure, operate, monitor and test SIMOCODE pro in
the field or from a central location. By displaying all operating,
service and diagnostics data, SIMOCODE ES supplies impor-
tant information on whether maintenance work is required or, in
the event of a fault, helps to prevent faults or to localize and rec-
tify them once they have occurred.
Unnecessary plant downtimes can be prevented by changing
parameters online (even during operation). The flexible printing
function integrated into SIMOCODE ES allows comprehensive
documentation of all parameters or partial documentation of
selected or changed parameters.
• SIMOCODE ES Graphic is an optional software package for
SIMOCODE ES Smart or SIMOCODE ES Professional. It
expands the user interface with a graphical editor and
supports extremely user-friendly parameterization with Drag &
Drop. Inputs and outputs of function blocks can be graphically
linked and parameters can be set. The configured functions
can be described in greater detail using comments and the
device parameterization can be documented graphically –
this speeds up start-up and simplifies the plant
documentation.
Note:
Installation of SIMOCODE ES Graphic requires at least one
installed version of SIMOCODE ES Smart 2004+SP1 or
SIMOCODE ES Professional+SP1 (from April 2005) on the
PC/PG.
OM SIMOCODE pro object manager
(as part of SIMOCODE ES Professional)
The OM SIMOCODE pro object manager is a standard
component of SIMOCODE ES Professional. In contrast to a
conventional GSD file, it enables SIMOCODE ES to be
integrated into STEP 7 for convenient device parameterization.
By installing SIMOCODE ES Professional and
OM SIMOCODE pro on a PC/PG, which is used to configure the
hardware of the SIMATIC S7, SIMOCODE ES Professional can
be called directly from the hardware configuration. This allows
easy and consistent S7 configuration.
PCS 7 function block library for SIMOCODE pro
The SIMOCODE pro PCS 7 library can be used for simple and
easy integration of SIMOCODE pro into the SIMATIC PCS 7 V6
process control system. The SIMOCODE pro PCS 7 function
block library contains the diagnostic and driver blocks
corresponding with the diagnostic and driver concept of
SIMATIC PCS 7 as well as the elements (symbols and faceplate)
required for operator control and process monitoring. The
application is integrated by graphic interconnection using the
CFC Editor.
The technological and signal processing functions of the
SIMOCODE pro PCS 7 function block library are based on the
SIMATIC PCS 7 standard libraries (driver blocks, technological
blocks) and are optimally tailored to SIMOCODE pro. Users who
previously configured motor feeder circuits using conventional
technology by means of signal blocks and motor or valve blocks,
can now easily switch to the SIMOCODE pro PCS 7 function
block library.
The SIMOCODE pro PCS 7 function block library supplied on
CD-ROM allows the user to run the required engineering
software on the engineering station (single license) including the
runtime software for executing the AS blocks in an automation
system (single license). If the AS blocks are to be used in
additional automation systems, the corresponding number of
runtime licenses are required which are supplied without a data
carrier.
System manual for SIMOCODE pro
The SIMOCODE pro system manual describes the motor
management system and its functions in detail. It contains
information about configuration and commissioning as well as
servicing and maintenance. A typical example of a reversing
starter application is used to teach the user quickly and
practically how to use the system. In addition to help on how to
identify and rectify faults in the event of a malfunction, the
manual also contains special information for servicing and
maintenance.
Furthermore, the manual contains schematics, dimensional
drawings and technical specifications of the system
components as configuring aids.
Siemens LV 1 T · 2006
7/13