AM186ED Datasheet, PDF (25/88 Pages) Advanced Micro Devices – High Performance, 80C186- and 80C188-Compatible, 16-Bit Embedded Microcontrollers

PRELIMINARY
INT4/PIO30
MCS0/PIO14
Maskable Interrupt Request 4 (input,
asynchronous)
Midrange Memory Chip Select 0 (output,
synchronous, internal pullup)
This pin indicates to the microcontroller that an This pin indicates to the system that a memory access
interrupt request has occurred. If the INT4 pin is not is in progress to the corresponding region of the
masked, the microcontroller then transfers program midrange memory block. The base address and size of
execution to the location specified by the INT4 vector in the midrange memory block are programmable. MCS0
the microcontroller interrupt vector table.
can be programmed as the chip select for the entire
Interrupt requests are synchronized internally, and can
be edge-triggered or level-triggered. To guarantee
interrupt recognition, the requesting device must
continue asserting INT4 until the request is
acknowledged.
middle chip select address range. This mode is
recommended when using DRAM since the MCS1,
MCS2, and MCS3 chip selects function as RAS and
CAS signals for the DRAM interface and are not
available as chip selects.
When pulse width demodulation mode is enabled, the
INT4 signal is used internally to indicate a High-to-Low
transition on the PWD signal. When pulse width
demodulation mode is enabled, INT4/PIO30 can be
used as a PIO.
LCS/ONCE0/RAS0
Lower Memory Chip Select (output, synchronous,
internal pullup)
T ^{ONCE Mode Request 0 (input)}
Row Address Strobe 0
LCS—This pin indicates to the system that a memory
access is in progress to the lower memory block. The
F base address and size of the lower memory block are
programmable up to 512 Kbytes. LCS is configured for
8-bit or 16-bit bus size by the auxiliary configuration
register.
LCS is three-stated and held resistively High during a
A _{bus hold condition. In addition, LCS has an ~9-kohm}
internal pullup resistor that is active during reset.
ONCE0—During reset, this pin and ONCE1 indicate to
the microcontroller the mode in which it should operate.
R ^{ONCE0 and ONCE1 are sampled on the rising edge of}
RES. If both pins are asserted Low, the microcontroller
enters ONCE mode; otherwise, it operates normally.
In ONCE mode, all pins assume a high-impedance
state and remain in that state until a subsequent reset
D _{occurs. To guarantee that the microcontroller does not}
inadvertently enter ONCE mode, ONCE0 has a weak
internal pullup resistor that is active only during reset.
MCS0 is configured for 8-bit or 16-bit bus size by the
auxiliary configuration register. MCS0 is three-stated
and held resistively High during a bus hold condition. In
addition, MCS0 has a weak internal pullup resistor that
is active during reset.
MCS1/UCAS/PIO15
Midrange Memory Chip Select (output,
synchronous, internal pullup)
Upper Column Address Strobe
This pin indicates to the system that a memory access
is in progress to the corresponding region of the
midrange memory block. The base address and size of
the midrange memory block are programmable. MCS1
is configured for 8-bit or 16-bit bus size via the auxiliary
configuration register.
MCS1 is three-stated and held resistively High during a
bus hold condition. In addition, MCS1 has a weak
internal pullup resistor that is active during reset.
If MCS0 is programmed to be active for the entire
middle chip-select range, then this signal is available
as a PIO or a DRAM control. If this signal is not
programmed as a PIO or DRAM control and if MCS0 is
programmed for the entire middle chip-select range,
this signal operates normally.
UCAS—When either bank of DRAM is activated, the
UCAS functionality is enabled. The UCAS activates
when the DRAM access is for the AD15–AD8 byte.
UCAS also activates at the start of a DRAM refresh
access.
RAS0—This pin is the row address strobe for the lower
DRAM block. The selection of RAS0 or LCS
functionality, along with their configurations, are set
UCAS is three-stated and held resistively High during a
bus hold condition. In addition, UCAS has a weak
internal pullup resistor that is active during reset.
using the LMCS register.
MCS2/LCAS/PIO24
RAS0 is three-stated and held resistively High during a
bus hold condition. In addition, RAS0 has a weak
internal pullup resistor that is active during reset.
Midrange Memory Chip Select (output,
synchronous, internal pullup)
Lower Column Address Strobe
This pin indicates to the system that a memory access
is in progress to the corresponding region of the
midrange memory block. The base address and size of
Am186ED/EDLV Microcontrollers
25