PIC24FJ256GB110-I Datasheet, PDF (300/328 Pages) Microchip Technology – 64/80/100-Pin, 16-Bit Flash Microcontrollers with USB On-The-Go (OTG)

PIC24FJ256GB110 FAMILY
TABLE 28-6: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD)
DC CHARACTERISTICS
Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
Parameter
No.
Typical⁽¹⁾
Max
Units
Conditions
Power-Down Current (IPD)⁽²⁾
DC60
DC60a
0.1
1
0.15
1
μA
-40°C
μA
+25°C
2.0V⁽³⁾
DC60b
3.7
18
μA
+85°C
DC60c
DC60d
0.2
1.3
0.25
1.3
μA
-40°C
μA
+25°C
2.5V⁽³⁾ Base Power-Down Current⁽⁵⁾
DC60e
4.2
27
μA
+85°C
DC60f
DC60g
3.6
9
μA
-40°C
4.0
10
μA
+25°C
3.3V⁽⁴⁾
DC60h
11.0
36
μA
+85°C
DC61
DC61a
1.75
3
1.75
3
μA
-40°C
μA
+25°C
2.0V⁽³⁾
DC61b
1.75
3
μA
+85°C
DC61c
DC61d
2.4
4
μA
-40°C
2.4
4
μA
+25°C
2.5V⁽³⁾ Watchdog Timer Current: ΔIWDT⁽⁵⁾
DC61e
2.4
4
μA
+85°C
DC61f
DC61g
2.8
5
μA
-40°C
2.8
5
μA
+25°C
3.3V⁽⁴⁾
DC61h
2.8
5
μA
+85°C
DC62
DC62a
2.5
7
μA
-40°C
2.5
7
μA
+25°C
2.0V⁽³⁾
DC62b
3.0
7
μA
+85°C
DC62c
DC62d
DC62e
2.8
7
μA
-40°C
3.0
7
μA
+25°C
2.5V⁽³⁾
RTCC + Timer1 w/32 kHz Crystal:
ΔRTCC + ΔITI32⁽⁵⁾
3.0
7
μA
+85°C
DC62f
DC62g
3.5
10
μA
-40°C
3.5
10
μA
+25°C
3.3V⁽⁴⁾
DC62h
4.0
10
μA
+85°C
Note 1: Data in the Typical column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance
only and are not tested.
2: Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as inputs and
pulled high. WDT, etc., are all switched off, VREGS bit is clear, and the Peripheral Module Disable (PMD)
bits for all unused peripherals are set.
3: On-chip voltage regulator disabled (ENVREG tied to VSS).
4: On-chip voltage regulator enabled (ENVREG tied to VDD). Low-Voltage Detect (LVD) and Brown-out
Detect (BOD) are enabled.
5: The Δ current is the additional current consumed when the module is enabled. This current should be
added to the base IPD current.
DS39897B-page 298
Preliminary
© 2008 Microchip Technology Inc.