PIC24FJ256GB110-I Datasheet, PDF (299/328 Pages) Microchip Technology – 64/80/100-Pin, 16-Bit Flash Microcontrollers with USB On-The-Go (OTG)

PIC24FJ256GB110 FAMILY
TABLE 28-5: DC CHARACTERISTICS: IDLE CURRENT (IIDLE)
DC CHARACTERISTICS
Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
Parameter
No.
Typical⁽¹⁾
Max
Units
Conditions
Idle Current (IIDLE)⁽²⁾
DC40
DC40a
220
290
μA
220
290
μA
-40°C
+25°C
2.0V⁽³⁾
DC40b
DC40d
DC40e
220
290
μA
300
390
μA
300
390
μA
+85°C
-40°C
+25°C
3.3V⁽⁴⁾
1 MIPS
DC40f
300
420
μA
+85°C
DC43
DC43a
0.85
1.1
mA
0.85
1.1
mA
-40°C
+25°C
2.0V⁽³⁾
DC43b
DC43d
DC43e
0.87
1.2
mA
1.1
1.4
mA
1.1
1.4
mA
+85°C
-40°C
+25°C
3.3V⁽⁴⁾
4 MIPS
DC43f
1.1
1.4
mA
+85°C
DC47
DC47a
4.4
5.6
mA
4.4
5.6
mA
-40°C
+25°C
2.5V⁽³⁾
DC47b
DC47c
DC47d
4.4
5.6
mA
4.4
5.6
mA
4.4
5.6
mA
+85°C
-40°C
+25°C
3.3V⁽⁴⁾
16 MIPS
DC47e
4.4
5.6
mA
+85°C
DC50
DC50a
1.1
1.4
mA
1.1
1.4
mA
-40°C
+25°C
2.0V⁽³⁾
DC50b
DC50d
DC50e
1.1
1.4
mA
1.4
1.8
mA
1.4
1.8
mA
+85°C
-40°C
+25°C
3.3V⁽⁴⁾
FRC (4 MIPS)
DC50f
1.4
1.8
mA
+85°C
DC51
DC51a
4.3
6.0
μA
4.5
6.0
μA
-40°C
+25°C
2.0V⁽³⁾
DC51b
DC51d
DC51e
7.2
25
μA
38
50
μA
44
60
μA
+85°C
-40°C
+25°C
3.3V⁽⁴⁾
LPRC (31 kHz)
DC51f
70
110
μA
+85°C
Note 1: Data in “Typical” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance
only and are not tested.
2: Base IIDLE current is measured with the core off, OSCI driven with external square wave from rail to rail.
All I/O pins are configured as inputs and pulled to VDD. MCLR = VDD; WDT and FSCM are disabled. No
peripheral modules are operating and all of the Peripheral Module Disable (PMD) bits are set.
3: On-chip voltage regulator disabled (ENVREG tied to VSS).
4: On-chip voltage regulator enabled (ENVREG tied to VDD). Low-Voltage Detect (LVD) and Brown-out
Detect (BOD) are enabled.
© 2008 Microchip Technology Inc.
Preliminary
DS39897B-page 297