|
PIC32MX320F032H_11 Datasheet, PDF (155/214 Pages) Microchip Technology – High-Performance, General Purpose and USB, 32-bit Flash Microcontrollers | |||
|
◁ |
PIC32MX3XX/4XX
TABLE 29-7: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD)
DC CHARACTERISTICS
Standard Operating Conditions: 2.3V to 3.6V (unless otherwise stated)
Operating temperature -40°C â¤TA â¤+85°C for Industrial
-40°C â¤TA â¤+105°C for V-Temp
Parameter
No.
Typical(2)
Max.
Power-Down Current (IPD)(1)
DC40
7
30
DC40a
24
30
DC40b
205
300
DC40h
450
900
DC40c
25
â
DC40d
9
70
DC40e
DC40g
25
70
115
200(5)
DC40f
200
400
DC40i
470
1200
Units
μA
-40°C
μA
+25°C
2.3V
μA
+85°C
µA
+105ºC
μA
+25°C 3.3V
μA
-40°C
μA
+25°C
μA
+70°C 3.6V
μA
+85°C
µA
+105ºC
Conditions
Base Power-Down Current (Note 6)
Base Power-Down Current
Base Power-Down Current
Module Differential Current
DC41
â
10
μA
-40°C
DC41a
DC41b
â
10
μA
+25°C
2.3V
Watchdog Timer Current: ÎIWDT (Notes 3, 6)
â
10
μA
+85°C
DC41g
â
12
µA
+105ºC
DC41c
5
â
μA
+25°C 3.3V
Watchdog Timer Current: ÎIWDT (Note 3)
DC41d
â
10
μA
-40°C
DC41e
DC41f
â
10
μA
+25°C
3.6V
Watchdog Timer Current: ÎIWDT (Note 3)
â
12
μA
+85°C
DC41h
â
15
µA
+105ºC
DC42
â
10
μA
-40°C
DC42a
DC42b
â
â
17
37
μA
+25°C
2.3V
μA
+85°C
RTCC + Timer1 w/32 kHz Crystal: ÎIRTCC
(Notes 3, 6)
DC42h
â
45
µA
+105ºC
DC42c
23
â
μA
+25°C 3.3V RTCC + Timer1 w/32 kHz Crystal: ÎIRTCC (Note 3)
DC42e
â
10
μA
-40°C
DC42f
DC42g
â
30
μA
+25°C
3.6V RTCC + Timer1 w/32 kHz Crystal: ÎIRTCC (Note 3)
â
44
μA
+85°C
DC42i
â
44
µA
+105ºC
Note 1: Base IPD is measured with all digital peripheral modules disabled. All I/Os are configured as inputs and
pulled low. WDT and FSCM are disabled.
2: Data in the âTypicalâ column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance
only and are not tested.
3: The Î current is the additional current consumed when the module is enabled. This current should be added
to the base IPD current.
4: Test conditions for ADC module differential current are as follows: Internal ADC RC oscillator enabled.
5: Data is characterized at +70°C and not tested. Parameter is for design guidance only.
6: This parameter is characterized, but not tested in manufacturing.
© 2011 Microchip Technology Inc.
DS61143H-page 155
|
▷ |