71M6541D Datasheet, PDF (40/166 Pages) Maxim Integrated Products – 0.1% Accuracy Over 2000:1 Current Range Energy Meter ICs

71M6541D/F/G and 71M6542F/G Data Sheet
Table 24: TMOD Register Bit Description (SFR 0x89)
Bit
Symbol
Timer/Counter 1
TMOD[7] Gate
TMOD[6] C/T
TMOD[5:4] M1:M0
Timer/Counter 0:
TMOD[3] Gate
TMOD[2] C/T
TMOD[1:0] M1:M0
Function
If TMOD[7] is set, external input signal control is enabled for Counter 1. The
TR1 bit in the TCON register (SFR 0x88) must also be set in order for Counter 1 to
increment. With these settings, Counter 1 increments on every falling edge of the
logic signal applied to one or more of the SEGDIO2-11 pins, as specified by the
contents of the DIO_R2 through DIO_R11 registers. See 2.5.8 Digital I/O and
LCD Segment Drivers and Table 47.
Selects timer or counter operation. When set to 1, a counter operation is performed.
When cleared to 0, the corresponding register functions as a timer.
Selects the mode for Timer/Counter 1, as shown in Table 22.
If TMOD[3] is set, external input signal control is enabled for Counter 0. The
TR0 bit in the TCON register (SFR 0x88) must also be set in order for Counter 0 to
increment. With these settings, Counter 0 is incremented on every falling edge of
the logic signal applied to one or more of the SEGDIO2-11 pins, as specified by
the contents of the DIO_R2 through DIO_R11 registers. See 2.5.8 Digital I/O and
LCD Segment Drivers and Table 47.
Selects timer or counter operation. When set to 1, a counter operation is
performed. When cleared to 0, the corresponding register functions as a timer.
Selects the mode for Timer/Counter 0 as shown in Table 22.
Bit
TCON[7]
TCON[6]
TCON[5]
TCON[4]
TCON[3]
TCON[2]
TCON[1]
TCON[0]
Table 25: The TCON Register Bit Functions (SFR 0x88)
Symbol
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
Function
The Timer 1 overflow flag is set by hardware when Timer 1 overflows. This flag
can be cleared by software and is automatically cleared when an interrupt is
processed.
Timer 1 run control bit. If cleared, Timer 1 stops.
Timer 0 overflow flag set by hardware when Timer 0 overflows. This flag can be
cleared by software and is automatically cleared when an interrupt is processed.
Timer 0 Run control bit. If cleared, Timer 0 stops.
Interrupt 1 edge flag is set by hardware when the falling edge on external pin int1 is
observed. Cleared when an interrupt is processed.
Interrupt 1 type control bit. Selects either the falling edge or low level on input pin
to cause an interrupt.
Interrupt 0 edge flag is set by hardware when the falling edge on external pin int0 is
observed. Cleared when an interrupt is processed.
Interrupt 0 type control bit. Selects either the falling edge or low level on input pin
to cause interrupt.
2.4.7 WD Timer (Software Watchdog Timer)
There is no internal software watchdog timer. Use the standard hardware watchdog timer instead (see
2.5.11 Hardware Watchdog Timer).
2.4.8 Interrupts
The 80515 provides 11 interrupt sources with four priority levels. Each source has its own interrupt request
flag(s) located in a special function register (TCON, IRCON, and SCON). Each interrupt requested by