R01DS0190EJ0100 Datasheet, PDF (57/110 Pages) Renesas Technology Corp – 32 MHz 32-bit RX MCUs, 50 DMIPS, up to 128 Kbytes of flash memory

RX111 Group
5. Electrical Characteristics
Table 5.11 DC Characteristics (9)
Conditions: VCC = AVCC0 = VCC_USB = 1.8 to 3.6 V, VSS = AVSS0 = VREFL0 = VSS_USB = 0 V, T_a = –40 to +105°C
Item
Symbol Min.
Typ.
Max.
Unit
Test
Conditions
Analog power
supply current
During A/D conversion
During D/A conversion (per channel)*¹
I_AVCC
—
0.7
1.2 mA
—
—
1.5
Temperature sensor
—
75
— μA
Reference
power supply
current
Waiting for A/D, D/A conversion (all units)
During A/D conversion
Waiting for A/D conversion (all units)
—
I_REFH0
—
—
—
0.3
25
52 μA
—
60 nA
USB operating During USB communication operation under the following I_USBH*² —
current
settings and conditions
4.3
(VCC)
— mA
 Host controller operation is set to full-speed mode
0.9
Bulk OUT transfer (64 bytes) × 1,
(USB_VCC)
bulk IN transfer (64 bytes) × 1
 Connect peripheral devices via a 1-meter USB
cable from the USB port.
During USB communication operation under the following I_USBF*² —
settings and conditions
3.6
(VCC)
— mA
 Function controller operation is set to full-speed
1.1
mode
(USB_VCC)
Bulk OUT transfer (64 bytes) × 1,
bulk IN transfer (64 bytes) × 1
 Connect the host device via a 1-meter USB cable
from the USB port.
During suspended state under the following setting and
conditions
I_SUSP*³ —
0.35
(VCC)
— μA
 Function controller operation is set to full-speed
170
mode (pull up the UDP0 pin)
(USB_VCC)
 Software standby mode
 Connect the host device via a 1-meter USB cable
from the USB port.
Note 1. The reference power supply current is included in the power supply current value for D/A conversion.
Note 2. Current consumed only by the USB module.
Note 3. Includes the current supplied from the pull-up resistor of the USB0_DP pin to the pull-down resistor of the host device, in addition
to the current consumed by this MCU during the suspended state.
Table 5.12 DC Characteristics (10)
Conditions: VCC = AVCC0 = VCC_USB = 1.8 to 3.6 V, VSS = AVSS0 = VREFL0 = VSS_USB = 0 V, T_a = –40 to +105°C
Item
Symbol
Min.
Typ.
Max.
Unit
Test Conditions
RAM standby voltage
V_RAM
1.8
—
3.6
V
Table 5.13 DC Characteristics (11)
Conditions: VCC = AVCC0 = VCC_USB = 0 to 3.6 V, VREFH0 = 0 to AVCC0, VSS = AVSS0 = VREFL0 = VSS_USB = 0 V,
T_a = –40 to +105°C
Item
Symbol Min.
Typ.
Max.
Unit
Test Conditions
Power-on VCC rising
gradient
At normal startup*¹
During fast startup time*²
SrVCC 0.02
—
0.02
—
20
ms/V
2
Voltage monitoring 1 reset
enabled at startup*^3, *⁴
0.02
—
—
Note 1. When OFS1.(STUPLVD1REN, FASTSTUP) = 11b.
Note 2. When OFS1.(STUPLVD1REN, FASTSTUP) = 10b.
Note 3. When OFS1.STUPLVD1REN = 0.
Note 4. Turn on the power supply voltage according to the normal startup rising gradient because the register settings set by OFS1 are
not read in boot mode.
R01DS0190EJ0100 Rev.1.00
Jun 19, 2013
Page 57 of 107