AMIS-30543 Datasheet, PDF (5/38 Pages) ON Semiconductor – Micro-Stepping Motor Driver

AMIS−30543
PACKAGE THERMAL CHARACTERISTICS
The AMIS−30543 is available in a NQFP32 package. For
The Rthja for 2S2P is simulated conform JEDEC
cooling optimizations, the NQFP has an exposed thermal JESD−51 as follows:
pad which has to be soldered to the PCB ground plane. The _{• A 4−layer printed circuit board with inner power planes}
ground plane needs thermal vias to conduct the heat to the
bottom layer. Figure 4 gives an example for good power
distribution solutions.
For precise thermal cooling calculations the major
thermal resistances of the device are given in Table 5. The
thermal media to which the power of the devices has to be
given are:
• Static environmental air (via the case)
• PCB board copper area (via the exposed pad)
The major thermal resistances of the device are the Rth
from the junction to the ambient (Rthja) and the overall Rth
from the junction to exposed pad (Rthjp). In Table 4 below
one can find the values for the Rthja and Rthjp, simulated
and outer (top and bottom) signal layers is used
• Board thickness is 1.46 mm (FR4 PCB material)
• The 2 signal layers: 70 mm thick copper with an area of
5500 mm² copper and 20% conductivity
• The 2 power internal planes: 36 mm thick copper with
an area of 5500 mm² copper and 90% conductivity
The Rthja for 1S0P is simulated conform to JEDEC
JESD−51 as follows:
• A 1−layer printed circuit board with only 1 layer
• Board thickness is 1.46 mm (FR4 PCB material)
• The layer has a thickness of 70 mm copper with an area
of 5500 mm² copper and 20% conductivity
according to JESD−51.
Figure 4. Example^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}of N^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}QF^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}P−3^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}2 PC^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}B G^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}ro^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}und^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}Pla^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}ne^NL^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉQ}a^Fy^Po^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ−}u³t^{2ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}in T^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}op V^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}iew^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}(P^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}refe^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}rred^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}La^{ÏÏÏÏÏÏÏÏÏÉÉÉÉÉÉÉÉÉ}yout at Top and Bottom)
ELECTRICAL SPECIFICATION
Recommend Operation Conditions
Operating ranges define the limits for functional
operation and parametric characteristics of the device. Note
that the functionality of the chip outside these operating
Table 3. OPERATING RANGES
Symbol
Parameter
V_BB
Analog DC Supply
T_J
Junction Temperature (Note 5)
5. No more than 100 cumulative hours in life time above T_tw.
ranges is not guaranteed. Operating outside the
recommended operating ranges for extended periods of time
may affect device reliability.
Min
Max
Unit
+6
+30
V
−40
+172
°C
http://onsemi.com
5