M1A3P250-1VQ100I Datasheet, PDF (7/210 Pages) Microsemi Corporation – ProASIC3 Flash Family FPGAs with Optional Soft ARM Support

ProASIC3 Flash Family FPGAs
Table 2-2 • Recommended Operating Conditions ¹
Symbol
Parameters ¹
T_J
VCC³
Junction temperature
1.5 V DC core supply voltage
Commercial
0 to 85²
1.425 to 1.575
Industrial
-40 to 100²
1.425 to 1.575
Units
°C
V
VJTAG
JTAG DC voltage
1.4 to 3.6
1.4 to 3.6
V
VPUMP
Programming voltage
Programming Mode
Operation ⁴
3.15 to 3.45
0 to 3.6
3.15 to 3.45
V
0 to 3.6
V
VCCPLL
Analog power supply (PLL)
VCCI and VMV ⁵ 1.5 V DC supply voltage
1.425 to 1.575 1.425 to 1.575 V
1.425 to 1.575 1.425 to 1.575 V
1.8 V DC supply voltage
1.7 to 1.9
1.7 to 1.9
V
2.5 V DC supply voltage
2.3 to 2.7
2.3 to 2.7
V
3.3 V DC supply voltage
3.3 V wide range DC supply voltage ⁶
3.0 to 3.3
2.7 to 3.6
3.0 to 3.3
V
2.7 to 3.6
V
LVDS/B-LVDS/M-LVDS differential I/O
2.375 to 2.625 2.375 to 2.625 V
LVPECL differential I/O
3.0 to 3.6
3.0 to 3.6
V
Notes:
1. All parameters representing voltages are measured with respect to GND unless otherwise specified.
2. Software Default Junction Temperature Range in the Libero SoC software is set to 0°C to +70°C for commercial, and -
40°C to +85°C for industrial. To ensure targeted reliability standards are met across the full range of junction
temperatures, Microsemi recommends using custom settings for temperature range before running timing and power
analysis tools. For more information regarding custom settings, refer to the New Project Dialog Box in the Libero SoC
Online Help.
3. The ranges given here are for power supplies only. The recommended input voltage ranges specific to each I/O
standard are given in Table 2-18 on page 2-18.
4. VPUMP can be left floating during operation (not programming mode).
5. VMV and VCCI should be at the same voltage within a given I/O bank. VMV pins must be connected to the
corresponding VCCI pins. See the "VMVx I/O Supply Voltage (quiet)" section on page 3-1 for further information.
6. 3.3 V wide range is compliant to the JESD8-B specification and supports 3.0 V VCCI operation.
Table 2-3 • Flash Programming Limits – Retention, Storage and Operating Temperature¹
Product
Grade
Commercial
Programming Program Retention
Cycles
(biased/unbiased)
500
20 years
Maximum Storage
Temperature T_STG (°C)²
110
Maximum Operating
Junction Temperature T_J (°C)²
100
Industrial
500
20 years
110
100
1. This is a stress rating only; functional operation at any condition other than those indicated is not implied.
2. These limits apply for program/data retention only. Refer to Table 2-1 on page 2-1 and Table 2-2 for device operating
conditions and absolute limits.
Table 2-4 • Overshoot and Undershoot Limits ¹
VCCI and VMV
Average VCCI–GND Overshoot or Undershoot
Duration as a Percentage of Clock Cycle²
Maximum Overshoot/
Undershoot²
2.7 V or less
10%
1.4 V
5%
1.49 V
3V
10%
1.1 V
5%
1.19 V
3.3 V
10%
0.79 V
5%
0.88 V
Revision 15
2-2