|
PIC16F1946 Datasheet, PDF (392/440 Pages) Microchip Technology – 64-Pin Flash-Based, 8-Bit CMOS Microcontrollers with LCD Driver and nanoWatt XLP Technology | |||
|
◁ |
PIC16F/LF1946/47
29.3 DC Characteristics: PIC16F/LF1946/47-I/E (Power-Down) (Continued)
PIC16LF1946/47
PIC16F1946/47
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ï£ TA ï£ +85°C for industrial
-40°C ï£ TA ï£ +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ï£ TA ï£ +85°C for industrial
-40°C ï£ TA ï£ +125°C for extended
Param
No.
D028
Device Characteristics Min.
Power-down Base Current (IPD)(2)
â
â
Typâ
0.1
0.1
Max.
+85°C
Max.
+125°C
Units
5
â
ïA
6
â
ïA
Conditions
VDD
Note
1.8 A/D Current (Note 1, Note 3), no
3.0 conversion in progress
D028
D029
D029
â
16
35
â
21
40
â
25
50
â
250
â
â
250
â
â
280
â
â
280
â
â
ïA
1.8 A/D Current (Note 1, Note 3), no
â
ïA
3.0 conversion in progress
â
ïA
5.0
â
ïA
1.8 A/D Current (Note 1, Note 3),
â
ïA
3.0 conversion in progress
â
ïA
1.8 A/D Current (Note 1, Note 3,
â
ïA
3.0 Note 4), conversion in progress
â
280
â
â
ïA
5.0
D030
D030
D031
â
3.5
7
â
7
9
â
17
38
â
21
50
â
22
70
â
1
â
â
10
â
â
ïA
1.8 Cap Sense, Low Power mode
â
ïA
3.0
â
ïA
1.8 Cap Sense, Low Power mode
â
ïA
3.0
â
ïA
5.0
â
ïA
3.0 LCD Bias Ladder, Low-power
â
ïA
3.0 LCD Bias Ladder, Medium-power
â
100
â
â
ïA
3.0 LCD Bias Ladder, High-power
D031
â
1.7
â
â
17
â
â
ïA
5.0 LCD Bias Ladder, Low-power
â
ïA
5.0 LCD Bias Ladder, Medium-power
â
170
â
â
ïA
5.0 LCD Bias Ladder, High-power
*
â
Legend:
Note 1:
2:
3:
4:
These parameters are characterized but not tested.
Data in âTypâ column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
TBD = To Be Determined
The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral ï current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
A/D oscillator source is FRC.
0.1 ïF capacitor on VCAP (RF0).
DS41414A-page 390
Preliminary
ï£ 2010 Microchip Technology Inc.
|
▷ |